Could change the coil resistance ?!!

[Ahmed Turky]

Hi buddies ..

I've istick pico 8 months ago with EC heads 0.3 ohms working properly .. i decided to change the coil being used and replace it with another one 0.5 ohms .. yet once connected the OLED screen is always giving "no atomizer" ..

Any ideas ?!!!!!

 

[Letitia]

Have you tried reseating the coil? Maybe your threads are off/not tight enough.

 

[Terry Koontz]

Hi buddies ..

I've istick pico 8 months ago with EC heads 0.3 ohms working properly .. i decided to change the coil being used and replace it with another one 0.5 ohms .. yet once connected the OLED screen is always giving "no atomizer" ..

Any ideas ?!!!!!

I’ve always dealt with that exact problem on my Pico.
In my case it was the atomizer screwed in to the mod too tight.
Try unscrewing and rescrewing it.
Don’ over tighten it.
Or the coil is not tight.

 

[Ahmed Turky]

Have you tried reseating the coil? Maybe your threads are off/not tight enough.

Thanks for ur reply ..

Actually i donna know how to be sure of the threads .. how to do so ?!!

 

[Ahmed Turky]

I’ve always dealt with that exact problem on my Pico.
In my case it was the atomizer screwed in to the mod too tight.
Try unscrewing and rescrewing it.
Don’ over tighten it.
Or the coil is not tight.

Thanks for ur reply ..

I'll try screwing it again .. i've tried 5 coils 0.5 ohms and all failed to work .. while 4 coils 0.3 ohms worked properly

 

[Terry Koontz]

Thanks for ur reply ..

I'll try screwing it again .. i've tried 5 coils 0.5 ohms and all failed to work .. while 4 coils 0.3 ohms worked properly

Thanks for ur reply ..

I'll try screwing it again .. i've tried 5 coils 0.5 ohms and all failed to work .. while 4 coils 0.3 ohms worked properly

That sounds like you got a pack of bad 0.5 ohm coils.

 

[Terry Koontz]

Thanks for ur reply ..

Actually i donna know how to be sure of the threads .. how to do so ?!!

When you get the no atomizer message, just twist the tank a little and see if the message goes away.

 

[Two_Bears]

Hi buddies ..

I've istick pico 8 months ago with EC heads 0.3 ohms working properly .. i decided to change the coil being used and replace it with another one 0.5 ohms .. yet once connected the OLED screen is always giving "no atomizer" ..

Any ideas ?!!!!!

Sounds like one end of tge coil isbt making contact.

When yoy rebuild yoy can build tge coil to almost any resistance

 

[Terry Koontz]

Thanks for ur reply ..

I'll try screwing it again .. i've tried 5 coils 0.5 ohms and all failed to work .. while 4 coils 0.3 ohms worked properly

Did you get both 0.3 and 0.5 ohm coils from the same vendor ?

 

[Ahmed Turky]

That sounds like you got a pack of bad 0.5 ohm coils.

Would say so except the 0.5 ohm coil that was in the original pack of my kit is not working too

 

[Ahmed Turky]

Did you get both 0.3 and 0.5 ohm coils from the same vendor ?

Yes i have the main pack of my kit with 2 coils .. one of them 0.3 ohm and the other one 0.5 ohm ..

The 0.3 ohm coil is working while the 0.5 ohm is not working too

 

[Terry Koontz]

Would say so except the 0.5 ohm coil that was in the original pack of my kit is not working too

is it the melo 3 tank you have on the pico ?
when i got mine both coils worked.

 

[Terry Koontz]

Yes i have the main pack of my kit with 2 coils .. one of them 0.3 ohm and the other one 0.5 ohm ..

The 0.3 ohm coil is working while the 0.5 ohm is not working too

what wattage are you using ?
maybe the wattage is too low for the 0.5 ohm coil.

 

[Ahmed Turky]

is it the melo 3 tank you have on the pico ?
when i got mine both coils worked.

Yes dear .. melo 3 tank .. the 0.3 ohm coil is working properly while the 0.5 ohm coil is not

 

[Ahmed Turky]

what wattage are you using ?
maybe the wattage is too low for the 0.5 ohm coil.

I usually adjust it +- 25 w ..

I'm not sure such wattage is proper for 0.5 ohm coil .. and what is the wattage suitable for 0.5 ohm ?!!

 

[Terry Koontz]

Well, I’m out of ideas.
That’s a very strange problem you have.
Hope somebody else has an answer for you.
Good luck.

 

[suprtrkr]

Hi and welcome. Just a guess, you have a bad coil. That does happen.

 

[Ahmed Turky]

Well, I’m out of ideas.
That’s a very strange problem you have.
Hope somebody else has an answer for you.
Good luck.

Thanx buddy

 

[Ahmed Turky]

Hi and welcome. Just a guess, you have a bad coil. That does happen.

I hope it's just the coil .. thanx buddy

 

[stols001]

I am not sure if it's the pack of coils, if it happened with the pre-installed 0.5 coil that came with it. This is rather odd, and if it were me, I'd either take your device to a B&M that can help you trouble shoot, or get in contact with the vendor who sold you the device and explain what problems you are having. They may be able to troubleshoot with you, as user error is always a possibility So is a mod that needs to be warrantied, that's equally a possibility.

Best of luck!

Anna