DIY project: Juice "spit" guard for 510Atty

[DJsoulk]

Posted an easy DIY project to help those that have Spitty 510 Atty's
Full post with step by step instructions.

I have been using standard size HH.357 510 Atty's. ENJOY!!

Hot vape spit guard

EDIT: BTW. If ya'll would like, I can repost the project on this forum.

 

[washvap]

Sounds like a good idea. Do you have a pic to the finished product?

WELCOME TO THE ECF

 

[mwa102464]

I've really been using these a lot with my 357's and other 1.5ohm Attys and it solves the issue spit on , here = Drip Tips | Universal |306 | 510 | Cherry Vape the extra length does it when you add your regular drip tip on top of the universal it works great, or you can also get one of these,pic below, the donut is awesome

 

[mwa102464]

Cant see your pics if not a member of the forum you show them on, could you post em here too so we can see what ya did please.

 

[DJsoulk]

Will post with pics later today. Gotta go to work.

 

[DJsoulk]

EDIT: Have more than 5 pics to post... I'll try to condense the pics into one 5 separate pics.

 

[DJsoulk]

DIY Spit guard for 510 atty's

Pics are in order of sequence. (Complete project spans 3 posts)

1. Tools and parts needed to complete project

2 & 3. Taking off the 801 connector end.

4. Pushing the atomizer innards out.

5. A glimpse inside the connector end of your now gutted 801 atty.

6. Exploded 801 atty.

7. 510 carto silicone rubber shipping cap (Closed end)

8. Size comparison of 510 shipping cap and a 801 atty connector.

9. 510 carto silicone rubber shipping cap (Open end)

10. Almost inside out 510 carto shipping plug.

11. Wire cutters clipping from 510 carto plug to create elliptical/oval hole

12. 510 carto plug with your awesome hole in closed end.

13. Exploded view of your components.
a. drip tip to 801 tube.
b. 510 rubber seal over 510 atty (elliptical/oval hole flush to top of atty)
c. Assembled 801 drip tip and tube over rubber seal and 510 atty assembly.

14. Sliding the tube over the rubber seal.

15. COMPLETED PROJECT!!

Additional photos:

1a. Long (standard) 801 spit guard (white) next to short barrel 801 spit guard.
2a. TIGHT LIKE A TIGER!!!
3a. FITS LIKE A GLOVE!!
4a. In order from left to right/Back to front (size comparison)
a. White 801 spit guard w/drip tip
b. Silver short 801 spit guard w/drip tip
c. 510 carto shipping cap (standing)
d. HH.357 2.0Ohm 510 on a GG TS connector cap.
e. Silver short 801 gutted tube
f. 510 carto shipping cap (laying cut)

GOOD LUCK and KEEP ME POSTED OF YOUR SUCCESSES OR IMPROVEMENT IDEAS!!! vape ON VAPEHEADS!

 

[DJsoulk]

I've really been using these a lot with my 357's and other 1.5ohm Attys and it solves the issue spit on , here = Drip Tips | Universal |306 | 510 | Cherry Vape the extra length does it when you add your regular drip tip on top of the universal it works great, or you can also get one of these,pic below, the donut is awesome

I was using the vapemate and a genie (vase) tip on my standard HH357 and was still getting juice spit back. However that Circle drip tip looks like it's the main contributor to why you don't get juice spit back in your face. Two passages for air is definitely better than one. Is the draw using that tip airy?

 

[DJsoulk]

Washvap, Just posted the project. A picture is worth a thousand words. If you have the parts give er' a try. And ping me back a like if it works out for you. I made this spit guard with both standard 801's and "shorty" 801's. Both have their merit's. And both keep the juice from getting to your mouth. Enjoy.