Does anyone make a 510 to 510 adapter?
- Thread starter Jaebihn
- Start date
- th_trl_thread_readers 0
- Status
Too much juice, not enough cleaning .. maybe?
I keep a pack of q-tips handy just for that reason, but I am getting much better at knowing when:
I actually need more juice, or
when I need to take the atty out, blow the crud out
and\or give it a good cleaning.
I keep a pack of q-tips handy just for that reason, but I am getting much better at knowing when:
I actually need more juice, or
when I need to take the atty out, blow the crud out
and\or give it a good cleaning.
I don't really mind cleaning it out. But it would be significantly easier if I could unscrew the 510 adapter and drop it into iso alcohol with my atty. And for a few bucks that would be worth it to me.
That might give 'a little' protection for your batteries, but if that adapter exists you'd have to hope it doesn't have that hole in the bottom, center and it leaks all over the place twice... 
I guess the proper term would be a 'male-to-female 510 adapter'... I haven't seen one, but I'm pretty new to all this.
I guess the proper term would be a 'male-to-female 510 adapter'... I haven't seen one, but I'm pretty new to all this.
I was just thinking about a 510 to 510 adapter myself. Not because of juice leakage, but in order to give me a little more cartomizer sticking out from my Riva cone. When I use 808 cartos with my 510 to 808 adapter, the carto sticks out just enough. When I use the 510 cartos, there isn't much sticking out. My lips hit the cone.
Maybe a 510 to 306 or 306 to 510 adapter? If such a thing exists. Same threads I think so I'm not sure if there is a need for one.
If anyone knows, please post.
Maybe a 510 to 306 or 306 to 510 adapter? If such a thing exists. Same threads I think so I'm not sure if there is a need for one.
If anyone knows, please post.
I'd like to find an extension like this so I could use Type B, mega cylinder atomizers on my BSB, without modifying the attys. I've used a combination of adapters for this, not totally satisfactory.
Typ0 you should check out FreedomSmokeUSA.com. They have 510 to 801 and a 801 to 510. I was just hoping I wouldn't have to buy 2 adapters to do this. Their adapters are 3 dollars. Its not about the money. I just don't want to connect 2 adapters if I don't have to.
I found this on another forum. Its a 510 to 510 but it looks like they took an atty and placed a connector on it. It looks pretty long and I don't think this is what I am looking for but it may help others out there.
TORNADO-Battery-Mains Charger Adaptor
TORNADO-Battery-Mains Charger Adaptor
I just found this:
http://www.e-cigarette-forum.com/forum/vaporflow/137270-new-adapters-stock.html
It is a post in the VaporFlow forum. (I am not affiliated with them)
On their site, it says:
Not all adapters are created equal! These are made to order from stainless steel.
So maybe, they can make a 510 to 510 adapter. If they can, they might also be able to close up the middle hole to prevent juice from going through. That might cause airflow issues though.
http://www.e-cigarette-forum.com/forum/vaporflow/137270-new-adapters-stock.html
It is a post in the VaporFlow forum. (I am not affiliated with them)
On their site, it says:
Not all adapters are created equal! These are made to order from stainless steel.
So maybe, they can make a 510 to 510 adapter. If they can, they might also be able to close up the middle hole to prevent juice from going through. That might cause airflow issues though.
tried this idea but it didn't work.
even with adaptor, you'll still need to clean the batt. and as often as you'd need to without the adaptor. The reason is that most fluid on the batt. is actually condensed vapor that goes the "wrong way" and not simply leaked fluid.
what u can do to minimize it is to make sure u don't release the -ve pressure at the end of the puff. take in all vapor.
even with adaptor, you'll still need to clean the batt. and as often as you'd need to without the adaptor. The reason is that most fluid on the batt. is actually condensed vapor that goes the "wrong way" and not simply leaked fluid.
what u can do to minimize it is to make sure u don't release the -ve pressure at the end of the puff. take in all vapor.
Or you can get a GGTS which has a collector tank to catch any drips and prevent from getting near the battery
I went to the site Type0holic mentioned and I left them a message. I will post my findings when they get back to me. I am hoping to get an adapter that is sealed (no hole) in the center so I can avoid the back flow vapor from getting to the battery well. My top is sealed. I am not worried about juice getting into the battery. I am hoping to minimize the amount of time I am cleaning that area. If I can just drop the adapter into isopropyl with my atty it would make cleaning a cinch.
I'm surprised I never thought of that. I usually only use my bottle fed mods myself, but I have a few friends that still drip, and complain about this. Gonna have to get ahold of a friend of mine in his machine shop to mill me out a few in his spare time.
Should be easy to make one. You need:
1) An old "busted" atty
2) A SEALED "battery connector" (like from an old battery).
3) Soldering skills - enough to solder a center connector wire on both sides
Use the old atty and solder a wire from center to center (use fairly heavy stranded wire - insulated of course) between the connectors. Make sure the centers connect without touching the outside "ground" - keep the exposed wire as short as possible. The center is the positive lead, the outside "shell" is the ground. Test it for no shorts!! You may wish to use some heat shrink tube. Epoxy works for gluing the parts in, or solder them in place.
You can get sealed connectors at Welcome to MadVapes LLC. See the modders section of the forum for more info and disclaimer stickies (at your own risk...etc.).
Have fun!
P.S. You have to remove the "guts" from the atty. Oh, and use lead-free solder just in case.....
1) An old "busted" atty
2) A SEALED "battery connector" (like from an old battery).
3) Soldering skills - enough to solder a center connector wire on both sides
Use the old atty and solder a wire from center to center (use fairly heavy stranded wire - insulated of course) between the connectors. Make sure the centers connect without touching the outside "ground" - keep the exposed wire as short as possible. The center is the positive lead, the outside "shell" is the ground. Test it for no shorts!! You may wish to use some heat shrink tube. Epoxy works for gluing the parts in, or solder them in place.
You can get sealed connectors at Welcome to MadVapes LLC. See the modders section of the forum for more info and disclaimer stickies (at your own risk...etc.).
Have fun!
P.S. You have to remove the "guts" from the atty. Oh, and use lead-free solder just in case.....
Last edited:
Thought you'd like to see what I've done with my Riva:
Riva with 510 CE2 v4 Cartomizer and Drip Tip
Riva with 510 Atomizer and DSE901 Whistle-Tip Cartridge
I'm going to try using 2 adapters. But here is what VaporFlow told me.
Jaebihn,
Thanks for contacting us.
We do not have the ability to make custom adapters at this time.
Our machine shop makes adapters for us with extremely high minimum quantities.
Let me know if there's anything else I can do for you.
Best,
Jason
President | Welcome To VaporFlow | Fine Electronic Cigarettes, Liquid & Accessories.
Jaebihn,
Thanks for contacting us.
We do not have the ability to make custom adapters at this time.
Our machine shop makes adapters for us with extremely high minimum quantities.
Let me know if there's anything else I can do for you.
Best,
Jason
President | Welcome To VaporFlow | Fine Electronic Cigarettes, Liquid & Accessories.
- Status
Similar threads
- Locked
