Just wondering if anyone on here had one. How would you rate it? Is it as good as a DNA30? Is it worth the price? How well does it vape? What's it's lowest ohms capability?
Dovpo Transformers E-mech
- Thread starter obsidian5889
- Start date
- th_trl_thread_readers 0
- Status
Yes. Received mine 3 days ago. Still putting it through it's paces, but have discovered the following:
The quality is very good, the screen functions work flawlessly.
If I can remember to lock the screen, it will stay where it's supposed to(very sensitive screen)
Still working on the wattage, but got the voltage down pat, and this is what I discovered about the voltage:
Set at 3 volts, the output is 5.1 volts
3.5=5.6
4.0=6.2
4.5=6.5
5.0=6.9
5.5=7.3
6.0=7.7
So, with this info I build a coil and it seems to preform according to the previous figures.
A 1.6ohm coil set at 3 volts is giving me 16 watts
The same coil set at 4 volts is giving a 24 watt vape.
Also have a .7 ohm build on another atty
set at 3 volts, it's producing 37 watts.
Have some more testing to do on the wattage setting,
but overall, knowing that the voltage output is this much higher, it's great.
The quality is very good, the screen functions work flawlessly.
If I can remember to lock the screen, it will stay where it's supposed to(very sensitive screen)
Still working on the wattage, but got the voltage down pat, and this is what I discovered about the voltage:
Set at 3 volts, the output is 5.1 volts
3.5=5.6
4.0=6.2
4.5=6.5
5.0=6.9
5.5=7.3
6.0=7.7
So, with this info I build a coil and it seems to preform according to the previous figures.
A 1.6ohm coil set at 3 volts is giving me 16 watts
The same coil set at 4 volts is giving a 24 watt vape.
Also have a .7 ohm build on another atty
set at 3 volts, it's producing 37 watts.
Have some more testing to do on the wattage setting,
but overall, knowing that the voltage output is this much higher, it's great.
looking for more info, im about to put money down on a pre-order this coming weekend.
I dunno, I just got in the pre-order line this morning though. $70 shipped for a duel 18650 30W setup sounded like a winner to me.
On the ohm's it's rated down to 0.50. That's enough for me.
On the ohm's it's rated down to 0.50. That's enough for me.
Last edited:
It looks like they aren't taking anymore pre-orders. They were this morning. It was $70 with free shipping. I added two Sony VTC5's for a grand total of $88.
DOVPO E-MECH – shopMasterVape.com
To anyone considering getting one of these, do not let my previous post discourage you. Apparently there may have been a few made,mine being one of those, that were not preforming properly. Not that I'm complaining.
Monday, 16 June 2014 05:47 posted by Everzon
Hi Eric,
We found some issues with some of the e-mech, we will improve them in the next version, which would be around 20th.
Monday, 16 June 2014 05:47 posted by Everzon
Hi Eric,
We found some issues with some of the e-mech, we will improve them in the next version, which would be around 20th.
Got mine off ebay yesterday for 108, really kinda hoping that mine is one that was not "performing properly" too bad my multimeter is broken
Got mine off ebay yesterday for 108, really kinda hoping that mine is one that was not "performing properly" too bad my multimeter is broken
i hate to say it but if it is already on hand for delivery it probably is one of the earlier ones that seem to run a little hot. just start low and adjust your watts slowly upward to prevent burning e-liquid or frying a coil. once you see where the proper setting is just keep it set lower and you should have no problem.... or you could cancel/return and wait for the new batch with the corrections. the wait seems worse than having to make an adjustment, but that's just me.....luckily, i am in a co-op($57 delivered) and ours will be from the updated newer batch...
Last edited:
hey all, been enjoying my e-mech, last night it would not charge, has anyone had a similar issue yet?
How accurate is your ohm reading on the device? Mine varies slightly like a DNA chip, like I throw in a 1.5 coil & my transformer reads about 1.7....
No It's Not Smoke
www.akavapers.com has the Transformer for $72.98 (In Stock) free shipping, their in Ca. & I had mine 3 days later to Mi. Awesome customer service!
No It's Not Smoke
Last edited:
Just got my v2 from my local vape shop yesterday! Love this mod. This is by far the best mod I have ever owned.
Question though. It goes up to 30w or 6v. I am currently using a .7 build on my kayfun at 6v, isn't that approx 51.4w? Or does it regulate to stop pushing past 30w? Anyone know the answer to this?
Question though. It goes up to 30w or 6v. I am currently using a .7 build on my kayfun at 6v, isn't that approx 51.4w? Or does it regulate to stop pushing past 30w? Anyone know the answer to this?
In voltage mode it goes over 30 watts. I've been using mine for a few months and only problem I've had is if i tighten the atty down all the way it says output short so i just loosen the beauty ring a little.works great
I was just looking at this. Do you know what version they have, V1, V2 or V3?
I just received a red e-mech and a blue cana mod. I like them equally. If I move a tank between the two I set it on the same watts and get the same result. The emech charges via mini USB as does the cana mod. The e-mech charges faster even though it has two 18650 v one in the cana. My son and I both have these two devices and we seem to have the same results. Performance to me is about equal other then the fact that the cana is a more consistent vape. The e-mech has one flaw that makes me crazy. It is easy to unlock the wattage setting and accidentally turn it up with out knowing it.
- Status
Similar threads
- Locked
