Egrip VT 1500mah

[salooo]

Hello, can some1 explain the diffrence between the devices mods, and the diffrent coils and their use?
coils are: CL-Ni Head , CL_Ti Head and CL 1.0 Ohm Head
and i experience leaking with the CL 1.0ohm coil, why would that happen its a brand new device i got earlier today.

The juice i use is Joyetech grape 11mg nicotine and it feels overwhelming kinda hurts my throat and lungs but its not a dry hit.

 

[MegaVaper]

There are different types of metals used to make the coils inside the head. Some heat up faster then others, some have better taste, and some have better durablility. Sometimes if your juice is too thin it can leak, or not enough cotton, or not closing the air holes while filling, or not screwing stuff down properly.

11 mg nic is pretty high for a direct lung hitter. Also if your new the vapor does take some getting use to. Took me like a day. Vapor seems denser then smoke.

 

[Canadian_Vaper]

CL-Ni Head: Ni200 Nickel Coil, only to be used in Temperature Control Mode for Nickel

CL_Ti Head: Titanium Coil, only to be used in Temperature Control Mode for Titanium.

CL 1.0 Ohm Head: A kanthal A1 coil, meant to be used in Variable Wattage mode.

If you use either of the Temperature Control coils in Wattage mode it will hurt your throat substantially as it will overheat and burn the juice instead of aerosolizing it.

 

[salooo]

CL-Ni Head: Ni200 Nickel Coil, only to be used in Temperature Control Mode for Nickel

CL_Ti Head: Titanium Coil, only to be used in Temperature Control Mode for Titanium.

CL 1.0 Ohm Head: A kanthal A1 coil, meant to be used in Variable Wattage mode.

If you use either of the Temperature Control coils in Wattage mode it will hurt your throat substantially as it will overheat and burn the juice instead of aerosolizing it.

i checked the additional rings and found the ring that is put on the coil, there is another ring for the base but there is a third ring and i dont know where its used, its a bit bigger than the coil's ring and a bit smaller than base's ring where would i use it? maybe it will finally stop my leaking issue

 

[Grimwald]

and to further confuse things, I use a 1.0 ohm CLR coil (which is the rebuildable version of the CL).

 

[salooo]

and to further confuse things, I use a 1.0 ohm CLR coil (which is the rebuildable version of the CL).

thanks for the confusion, how is it working for you? any leaks and what rate of juice do you use with it

 

[Grimwald]

thanks for the confusion, how is it working for you? any leaks and what rate of juice do you use with it

I like the clr over all of the others. I use them in several tanks as well as the egrip. I also rebuild them. I find the clr leaks less than any of the other coils.

In the egrip, there is a small silicon disk that you put on top of the coil. This does not seem to fit correctly on the clr. But if you unscrew the top piece a bit it will fit. I might get a drip now and then from the airflow hole, but it is unusual.

I vape way down around 8 watts and go thru 6-7 mil per day on all of my devices combined. The egrip is more of a grab and go, out and about device for me. The egrip is not a juice hog. I run out of battery long before I run out of juice.

 

[salooo]

I like the clr over all of the others. I use them in several tanks as well as the egrip. I also rebuild them. I find the clr leaks less than any of the other coils.

In the egrip, there is a small silicon disk that you put on top of the coil. This does not seem to fit correctly on the clr. But if you unscrew the top piece a bit it will fit. I might get a drip now and then from the airflow hole, but it is unusual.

I vape way down around 8 watts and go thru 6-7 mil per day on all of my devices combined. The egrip is more of a grab and go, out and about device for me. The egrip is not a juice hog. I run out of battery long before I run out of juice.

at the moment im still using the joyetech juice, at 9 or 8 watt and the leaking is almost gone but i still get a tiny tiny bit of juice get to my mouth every now and then. and there is one more disturbing thing that happens; the juice leaks a bit from the bottom periphery where the screws hold a plate to the bottom of the device i feel like there is a bit of space there and juice gets out from it. i tried screwing them a bit more but i cant seem to turn them at all.