Eleaf Istick help needed

[jdrake4200]

I would have posted to the other open thread, nut I am not allowed yet.

I have purchased an eleaf istick, and this thing vapes hot. I have looked everywhere for what I am about to ask you, but I can find no charts or any information. I do not have the money to buy the equipment needed to answer this question.

My normal vape is a 2.1 ohm coil at 4.3 volts. Now, with this device being tuned to MEAN and not RMS, I am unsure where a true 4.3 volts is on this device. Can someone please let me know what setting to put this device at so that I get a true 4.3 volts?

You guys are now my only hope of having the perfect vape with a very stealthy device that has the battery capacity I want. With any luck the Chinese company making this will tune to RMS going forward if they release a V2.

 

[leekeylee]

http://m.youtube.com/watch?v=_W1G7p_fCJw

The above review by PBusardo will give you all the details when he puts it on his scope

 

[jdrake4200]

I have watched this and it does not give me what I am looking for. He does his test in watts and it is too high for what I am looking for.

 

[r77r7r]

I'm at 2 watts under from my other equipment. But it's not perfect, they're Leafwatts.

 

[edyle]

I would have posted to the other open thread, nut I am not allowed yet.

I have purchased an ELEAF ISTICK, and this thing vapes hot. I have looked everywhere for what I am about to ask you, but I can find no charts or any information. I do not have the money to buy the equipment needed to answer this question.

My normal vape is a 2.1 ohm coil at 4.3 volts. Now, with this device being tuned to MEAN and not RMS, I am unsure where a true 4.3 volts is on this device. Can someone please let me know what setting to put this device at so that I get a true 4.3 volts?

You guys are now my only hope of having the perfect vape with a very stealthy device that has the battery capacity I want. With any luck the Chinese company making this will tune to RMS going forward if they release a V2.

It is the RMS which is correct.

 

[jefsview]

You can still read the main iStick thread.

http://www.e-cigarette-forum.com/forum/variable-voltage-apv-discussion/601111-eleaf-istick.html

As far as volts, it was stated that the displayed volts is about 1 volt too high. So, if you want to run @ 4.3 volts, dial it down to 3.3 volts on the istick... or as most do, dial to taste.

 

[Fattlestar]

Always start low and build up. I think you'll find ~3-3.4 volts to be the sweet spot in iStick's "special" voltage.

 

[pokemom]

Just go down by 1 - 1.5 watts.


Sent from my iPhone using Tapatalk

 

[jdrake4200]

Thank you for the replies. I was just hoping someone could give me the specific information I was looking for. Also I have gone through almost the entire Istick thread in the information I was looking for is not in there. If anyone has the equipment to find out for me it would begreatly appreciated.

 

[zhforest]

each device its spec, you need to found your hot spot.

 

[Woofer]

Always start low and build up. I think you'll find ~3-3.4 volts to be the sweet spot in iStick's "special" voltage.

hehe, that mirrors my experience!

 

[joesquid]

In order to figure out what you want you would need an o'scope to find frequency and duration of the positive transition of the square wave as well as the peak voltage. Oh yeah, and a decent calculator. I think it would be much easier to just dial it down until it tastes right. (or buy an MVP)

 

[Katya]

You can still read the main iStick thread.

http://www.e-cigarette-forum.com/forum/variable-voltage-apv-discussion/601111-eleaf-istick.html

As far as volts, it was stated that the displayed volts is about 1 volt too high. So, if you want to run @ 4.3 volts, dial it down to 3.3 volts on the istick... or as most do, dial to taste.

Oh, the Eleaf volts!

Dear OP--start at the lowest setting and you should be fine. Istick's 3 volts is somewhere around 4.2, or thereabouts. You should be fine with your 2.1 coil. It is a single coil atty, correct?