Evod 2 - New & Old Coils Leave Juice on Terminal

[Penumbra]

I have been using my Evod2 dual-coil tank for 2 weeks now. The problem is that, following EVERY hit, there is ALWAYS little drops of juice on the terminal of my iStick 50... or Evod-Style battery... basically anthing it connects to.

I have searched and searched about this issue, but never find anything that describes THIS kind of "leaking."

It came with the new style of dual-coils; however, I have purchased a pack of the older ones (since I am goin to rebuild this, and older style is easier to disassemble). Someone at local store, after my explanation of the "kind" of leaking i am having an issue with, said its just a bad coil... BUT, it does it with the replacement I installed.

I have a Vaporfi Platinum tank (which is same as a Kanger Pro), and those attys do the EXACT SAME thing.

Is there any way to fix this?

The problem is not THAT much of an issue with me, cuz I only hit it approx. 3 times a day. I use my 70pg / 2.4% nic juice with it, in contrast to the Atlantis sub-ohm that I "chief" on a lot throughout the day for lower nic and higher vg.

I use evod2 no higher than 3.7V (about 9 Watts w/ 1.5 Ohm coils).

Is it possible to fix this?

Thanks friends in "e-cig forum land"!!

 

[Robert Cromwell]

I have heard that you should remove the rubber boot from an extra coil and put it on the coil post upside down in addition to the other boot and this will fix the issue.
Not had the problem myself, but expecting some evod clones in the mail so did some research.

 

[Penumbra]

its funny you mention that... i read that one; however, that would help the seal up near the interface between chimney and atty but i think that is a solution to a different kind of leak. How could that "joining-point" fix small droplets that appear on the terminal?

Am i wrong in that assumption though?.. and the solution you provide IS the fix for my specific issue?

 

[Maiar]

Are we talking about little drops on the connector pin in the battery? If so, that's pretty normal and nothing to worry about. Just use a cotton swab to clean it off when you're done for the day. If you like the performance of the evod2 though, you can get a mini protank3. It's basically the same deal but glass. And you can get an airflow control valve for super cheap for them. Then the coil screws into that instead the normal base, and that keeps the liquid off the battery. At least it does with my full size protank2's and EMOW's.

 

[Penumbra]

Are we talking about little drops on the connector pin in the battery? If so, that's pretty normal and nothing to worry about...

Well alright then... thats' EXACTLY what it is. The tiniest amount of droplets... like, "you really have to shine the light on the pin and look closely" kind-of-thing.

If you like the performance of the evod2 though, you can get a mini protank3. It's basically the same deal but glass. And you can get an airflow control valve for super cheap for them. Then the coil screws into that instead the normal base, and that keeps the liquid off the battery. At least it does with my full size protank2's and EMOW's.

Have you ever heard of a company called Vaporfi? Though it took me too long to notice this (and by "too long" I mean, I spent too much damn money on "their" products), they basically take Kanger products, put their own name on them and perhaps change some aesthetic characteristics... but same stuff... just marked-up by 200 to 400%+!!!

I had bought their "Platinum Tank." I will put a link below. Tell me if you think its a Pro Tank?.. I think it is.

Anyways, I actually sent back the "Airflow" mechanism, and thought it didn't really do ....e for me personally... to-each-his/her-own


Link to Vaporfi Platinum Tank: VaporFi PLATINUM Clearomizer Tank - Tanks - Vaporizer Accessories