Genesis RSST and Kamry k200

[joaquingt]

Hi guys, i have a Kamry k200 and i want to try the Genesis RSST.

Is the k200 able to use the Genesis RSST ?
there is a lot of options of wire 28, 30, 32 and 400 and 500 mesh, also prerolled meshs.

what should i get to start runing the Genesis with my k200 ?

thanks for your advice.

 

[vapo jam]

k200 is the vv one, correct? you should probably go with 30 AWG wire to keep the resistance up (can't fire sub-ohm coils on most regulated mods). mesh depends on your juice - higher number mesh (500) wicks thinner juice better, lower number (300) wicks thicker juice better. 400 is probably a good compromise to get you started.

also, please read all of the safety information and watch lots of videos. yes, a regulated mod is safer than a mech mod when you're setting up an rba, but you still can damage your equipment and/or hurt yourself if you don't know what you're doing.

 

[joaquingt]

k200 is the vv one, correct? you should probably go with 30 AWG wire to keep the resistance up (can't fire sub-ohm coils on most regulated mods). mesh depends on your juice - higher number mesh (500) wicks thinner juice better, lower number (300) wicks thicker juice better. 400 is probably a good compromise to get you started.

also, please read all of the safety information and watch lots of videos. yes, a regulated mod is safer than a mech mod when you're setting up an rba, but you still can damage your equipment and/or hurt yourself if you don't know what you're doing.

thank you very much, yeah the k200 is vv/vw ill get 400 an 30 wire

 

[vapo jam]

good luck!

have you set up a gennie before? if not, please please PLEASE read up on it A LOT before you try. and be prepared to be frustrated - my first time it took me about 10 hours of rolling, coiling, fiddling, etc. to get it working properly, and from what i've heard, that's a relatively quick first set-up...

that being said, just try to have some patience and know that once you get it working properly, you'll NEVER go back to carto's, clearo's, etc.

 

[joaquingt]

good luck!

have you set up a gennie before? if not, please please PLEASE read up on it A LOT before you try. and be prepared to be frustrated - my first time it took me about 10 hours of rolling, coiling, fiddling, etc. to get it working properly, and from what i've heard, that's a relatively quick first set-up...

that being said, just try to have some patience and know that once you get it working properly, you'll NEVER go back to carto's, clearo's, etc.

thanks for your advice, i already watched a lot of videos and im prepared to have bad time lol

 

[T1lVl]

It's not hard at all. Don't be scared. All I use are genesis now and been doing it maybe 3 weeks. Had my first coil and wick rolled with 10 15 minutes. Now can literally roll a wick and wire in about 5 along with hitting my desire ohm.

 

[joaquingt]

maybe this will be usefull for someone, the k200 is a nice mod for clearos or vivis, the voltage drop is horrible, battery eater, the minimum voltage you can get is 3.6 (if you set it to work with 3.0, it will work at 3.6), the tread and the center floating ping is nice if i compare it with my vamo v3 the k200 is trash, not even good to read sub-ohm coils on attys, i sold my vamo v3 im keeping the k200 if i ever want to fire an old clearo. so if you thinking to buy a k200 DONT DO IT, i dont use vv or vw mods anymore since i started sub ohming with my zenesis i cant get a way from genesis attys, those are great.

Good luck guys