GLV3 not firing
- Thread starter tjc516
- Start date
- th_trl_thread_readers 0
- Status
Yeah just called and left him a message, just have to wait to hear back from him.
I checked the voltage coming out from the atomizer connector and its coming back around 6 volts.. seems like that should be ok..
Guess we'll see, just really annoyed just purchased this from a member and should be working..
I checked the voltage coming out from the atomizer connector and its coming back around 6 volts.. seems like that should be ok..
Guess we'll see, just really annoyed just purchased this from a member and should be working..
Try pulling the center post of the atomizer out just a tiny bit, it might not be completing the connection.
Also double check that the needle isn't shorting at the atty. It shouldn't touch the sides of the GLV head cap and I know that some of them shipped with the needle just a little too long. Check by taking the 3 apart and standing the housing on its head. The needle should be the same height roughly as the top of the "bottle cap" If the needle is too long it will go to short at the atty and possibly cause your batteries to go into protect mode.
Thanks for all the help guys i really appreciate it. I tried all suggestions and no joy, but then after staring at in in disgust for a few minutes it must have started to feel bad and started to work.
Only problem i'm noticing now is that it doesnt hit consistently, sometimes a great hit sometimes no hit.. Weird..
Only problem i'm noticing now is that it doesnt hit consistently, sometimes a great hit sometimes no hit.. Weird..
Try taking it off the feeder without changing a thing and see if it's hitting. If it is, then the juice post is probably shorting the atty.
If not, try Keyzy's idea. I didn't get an allen wrench but found one around the house that fits. It's worth a shot.
For bottom feeding the juice post on my feeder comes up a bit over the top of the feeder.
If not, try Keyzy's idea. I didn't get an allen wrench but found one around the house that fits. It's worth a shot.
For bottom feeding the juice post on my feeder comes up a bit over the top of the feeder.
mine won't fire either
took it off and no go. i've adjusted the thing up and down and still nothing. it was fine until i changed batteries and then it was week for awhile and nothin. oh Jay! call back soon....
took it off and no go. i've adjusted the thing up and down and still nothing. it was fine until i changed batteries and then it was week for awhile and nothin. oh Jay! call back soon....
took the top cap off and don't know why that helped but
sometimes works and sometimes not
i think Jay is ubber busy as no call back yet
Sara's update on the site says they are almost moved into the new shop and I think things have been hectic for them so maybe give him another call today and see if he is available.He is usually good at getting back with people.
Supper nice? So he makes a good dinner? 
These two (three now?) are top notch people... I think I called three times waiting for my SM and they didn't even seem annoyed, not in the slightest.
And I work in the restaurant business, so I know when people are pretending not to be annoyed!
These two (three now?) are top notch people... I think I called three times waiting for my SM and they didn't even seem annoyed, not in the slightest.
And I work in the restaurant business, so I know when people are pretending not to be annoyed!
Last edited:
smarty pants!!
Hi, I'm Monarch, nice to meet ya...
I hope he can get that fixed up for ya soon... I would have been a sad panda if I had waited for my GLV and it was haunted with a mischievous spirit...
Hopefully the ghosts in the ol winery are friendly ghosts, and don't mess with our vapor!
I hope he can get that fixed up for ya soon... I would have been a sad panda if I had waited for my GLV and it was haunted with a mischievous spirit...
Hopefully the ghosts in the ol winery are friendly ghosts, and don't mess with our vapor!
Last edited:
- Status
Similar threads
