Goblin mini
- Thread starter Mr universe
- Start date
- th_trl_thread_readers 0
- Status
mine using 26g kanthal 2.5mm 6wraps, dual on it came out 0.5ohm. It taste great, for me. 
If you're getting dry hits it probably has to do with wicking not the coil you're making. Make sure to watch some videos on how to wick it. I spend a lot of time trimming the wicks to go just barely into the channels, but thicken right after so the juice has somewhere to go.
I tried once using single coil but the smoke is not that thick as you using double coil
Sent from my iPhone using Tapatalk
My vapor production is quite good for a single coil. I don't like dual coils because with 2 coils you have twice the coil problems and 4x the wick problems.
I use Japanese cotton. I separate them into three sheets and cut them into rectangles and roll the cotton up, stick it in cut them and fluff the ends... But with the goblin you have to trim the ends and lead those tails into the juice channel but not stuffed to the point that you're not pulling in liquid.
im using M80, with power mode. 15.5watts is my sweet spot with 100% opened air hole. I think you should decrease your wraps because the deck is small and cooling isn't fast enough thats why you got the burn taste? Or you check whether your cotton has break apart?
The build in the pic is a dual coil, 28g, 3mm ID, 0.5ohm (can't remember the wrap count, maybe 6).
Great vape at 25w!
3mm ID, is a very tight fit in the GM.
I've recently been building: dual coil, 2.5mm ID, 7wraps, 0.62ohms
Fantastic vape at 27-30w
Never leaks or dry hit
Great vape at 25w!
3mm ID, is a very tight fit in the GM.
I've recently been building: dual coil, 2.5mm ID, 7wraps, 0.62ohms
Fantastic vape at 27-30w
Never leaks or dry hit
You using kathal or whatThe build in the pic is a dual coil, 28g, 3mm ID, 0.5ohm (can't remember the wrap count, maybe 6).
Great vape at 25w!
View attachment 494575
3mm ID, is a very tight fit in the GM.
I've recently been building: dual coil, 2.5mm ID, 7wraps, 0.62ohms
Fantastic vape at 27-30w
Never leaks or dry hit
Cause I just rebuild kanthal 26gauge 7 wraps 2.5mm
Sent from my iPhone using Tapatalk
Thanks to you dude and I think it's because of my cotton I didn't put it properly
Sent from my iPhone using Tapatalk
You using kathal or what
Cause I just rebuild kanthal 26gauge 7 wraps 2.5mm
Sent from my iPhone using Tapatalk
Yes @Mr universe I'm using Kanthal. I'm using 28g you are using 26g.
When using Kanthal on the SXMM you should be in Power mode, not Joule mode. Joule mod is for temp sensing wire, either ni200, or Ti Gr1 has native support on the SXMM with their latest firmware.You using kathal or what
Cause I just rebuild kanthal 26gauge 7 wraps 2.5mm
Sent from my iPhone using Tapatalk
GMini builds, eh? 26g kanthal 7-8 wraps 2.5mm ID is pretty good, that's what I'm using in my non-TC Gmini right now. Due to the small chamber / build deck you don't really have a lot of options, but that basic dual coil build seems to be pretty good for me.
Then how about nichrome isit a temp sensing wire too?
Sent from my iPhone using Tapatalk
No, nichrome is not temp wire, use that in Power mode as well.
Only wires for TC (joules mode) on the SX Mini M class are ni200, and Ti Gr1.
- Status
Similar threads
