how to drip ?

[Macarius]

Hi all,
Thanks in advance for your support.

Ok the question is I have a Magma clone rda uaing it in sigle coil mood always, when i have to drip i always have to unscrew it.
It has a deep well shall i just fill the whole well with cotton ?

Is there any way I can drip it by just removing the drip tip.

Kindly share some wicking tips and pictures if possible.

Thanks

 

[Ou2mame]

I drip in the 510 hole, just don't over fill. When I wick mine I bend the cotton down into the well. With only a single coil you can't out nearly as much juice in cause there won't be enough cotton to absorb it. When you tilt it the wrong way it'll get in the air hole without the cotton.

 

[Macarius]

I drip in the 510 hole, just don't over fill. When I wick mine I bend the cotton down into the well. With only a single coil you can't out nearly as much juice in cause there won't be enough cotton to absorb it. When you tilt it the wrong way it'll get in the air hole without the cotton.

I c thanks for information.
It means cotton can suck up the juice from well also and I dont need to put juice directly on coil?

So it is better if i use dual coil ?

Thanks

 

[tjeco]

Hi all,
Thanks in advance for your support.

Ok the question is I have a Magma clone rda uaing it in sigle coil mood always, when i have to drip i always have to unscrew it.
It has a deep well shall i just fill the whole well with cotton ?

Is there any way I can drip it by just removing the drip tip.

Kindly share some wicking tips and pictures if possible.

Thanks

Whatever suits your fancy You can either drip directly in your Drip Tip, or you can always open your TopCap and drip directly in your coils and in your juice well

Personally, I would remove the TopCap, put about 3 drops in the Coils and fill the Magma's Juice Well with 20 drops of Juice, being that the Magma has a pretty DEEP JuiceWell and that's how I've been using my Velocity.

 

[Thrasher]

You get used to a dripper and you can feel how much to refill and when.

All my attys I just pull the drip tip and count. Usually 10 drops for this dripper 15 for that one etc.

On one or two the drip tip hole is big enough to drip right into it (thats why they are called drip tips BTW)

 

[crxess]

Magma well can easily deal with a single coil build.

Leave the Wick tails long and cross then in the well. It may come close to filling the well. I use short wicks in dual coil and almost completely fill the well.
Always set your Magma with the air holes to the sides and wick facing you.that should minimize any chance of leaking.

 

[K_Tech]

Hi all,
Thanks in advance for your support.

Ok the question is I have a Magma clone rda uaing it in sigle coil mood always, when i have to drip i always have to unscrew it.

The Magma is still one of my favorite "flavor" drippers, and I still use it pretty regularly. I have (almost) always used mine in dual coil mode, but that's just my preference. In single coil mode, it's still a good performer.

It has a deep well shall i just fill the whole well with cotton ?

Some do, but I like to cut my wick just long enough to touch the bottom of the drip well with not a lot extra. I like the way it performs that way.

Is there any way I can drip it by just removing the drip tip.

Absolutely, or use a "wide bore" tip and drip straight through the drip tip as has already been mentioned.

Kindly share some wicking tips and pictures if possible.

Thanks

This is pretty much what I do:

 

[Macarius]

Thank you everyone for the replies
They are quite helpful
Thank you for the video K Tech.

I got the idea of dripping i will try the crxess tip about keeping the wick longer and towards the other end

Thanks again everyone
Best wishes (y)

 

[Blackboar]

When I use to drip with the Magma, I also chose to run it single coil. I would plug the other airflow hole on the deck with a piece of a round toothpick. That prevented some of the leaking you get around the AFC ring.

When I dripped, I used about 1/3 of a dropper, stick it down the drip tip and just squirted the juice into the juice well. 1/3 of a dropper tube was the perfect amount of juice for the well to prevent leaking. I also use a Delrin wide bore driptip from Cherry Vapes so the dropper tube fit inside with ease. If you use a smaller diameter drip tip, just tilt the atty towards the plugged side (slightly) and squirt.

 

[Macarius]

When I use to drip with the Magma, I also chose to run it single coil. I would plug the other airflow hole on the deck with a piece of a round toothpick. That prevented some of the leaking you get around the AFC ring.

When I dripped, I used about 1/3 of a dropper, stick it down the drip tip and just squirted the juice into the juice well. 1/3 of a dropper tube was the perfect amount of juice for the well to prevent leaking. I also use a Delrin wide bore driptip from Cherry Vapes so the dropper tube fit inside with ease. If you use a smaller diameter drip tip, just tilt the atty towards the plugged side (slightly) and squirt.

I c thanks for the tip.

I am using the stock driptip which came with it dont have any wide bore one, now thinking of buying one for magma

 

[edyle]

Hi all,
Thanks in advance for your support.

Ok the question is I have a Magma clone rda uaing it in sigle coil mood always, when i have to drip i always have to unscrew it.
It has a deep well shall i just fill the whole well with cotton ?

Is there any way I can drip it by just removing the drip tip.

Kindly share some wicking tips and pictures if possible.

Thanks

With my first magma I used to unscrew also; helps to see the condition inside; but after a while you get the hang of it and know what to expect; then you just drip by removing the drip tip.

At first I used to use alot of cotton; gives the liquid somewhere to stick to instead of sloshing around and maybe leaking.

my first magma i used single coil; stuffed the other side with foil; worked pretty good; it was a 30mm magma, and would take like 50+ drops.

 

[Macarius]

With my first magma I used to unscrew also; helps to see the condition inside; but after a while you get the hang of it and know what to expect; then you just drip by removing the drip tip.

At first I used to use alot of cotton; gives the liquid somewhere to stick to instead of sloshing around and maybe leaking.

my first magma i used single coil; stuffed the other side with foil; worked pretty good; it was a 30mm magma, and would take like 50+ drops.

I see i also have 30mm one
Why closing the other hole ? To prevent leaking or close and remove the airflow ring ?

 

[edyle]

I see i also have 30mm one
Why closing the other hole ? To prevent leaking or close and remove the airflow ring ?

I blocked up the hole so that when i lay my mod down horizontally with the 1 airhole facing up, the liquid wont leak through the other airhole.

But if you keep your mod upright all the time, using the airflow ring should suffice to keep the extra air out and not have to also worry about leaking.

 

[Macarius]

I blocked up the hole so that when i lay my mod down horizontally with the 1 airhole facing up, the liquid wont leak through the other airhole.

But if you keep your mod upright all the time, using the airflow ring should suffice to keep the extra air out and not have to also worry about leaking.

Ok got the point, never thought about that haha.

Thanks a lot for your help