I really like the aspire cleito expect a couple things..

[erikbal]

I recently upgraded from my old 50w istick Atlantis 1 combo to a rx200 with the crown on top. I really like it. Well now that I have enough power I'd like to try out some different tanks. I ordered a black aspire cleito and received it not too long ago. First impressions were great. I like the design and the black on black looks great. Massive airflow and very easy to fill. Was running perfectly with the .4 ohm coil then out of nowhere once in a while I'd get a dry hit that would burn my throat. Running between 70 and 80vg. Today I decided to take it apart and clean it good then try out the new .2 ohm coil with some milkman. Anyways I could NOT get the glass off. It was so bad I ended up breaking it trying to take it apart. Letting it prime good now then going to try it. Anyone else had these issues? Any tips or advice? Also when I put the spare glass on it didn't want to stay on good till I tightened the top.

Sent from my VS980 4G using Tapatalk

 

[Hobbs]

I don't have a Cleito but had a similar issue with a Melo 2, even insofar as breaking the glass trying to get it off. Eleaf support was no help other than "be careful".

What worked, was to leave the tank screwed together, BUT, unscrew the base until just a couple of threads were holding it all together. What that did was leave a space between the base o-ring and the bottom edge of the glass ... (the o-ring will act as a cushion)

THEN, I stood the tank straight up (and/or in a tank stand) and used my thumbnails along the top edge of the glass with downward pressure on either side of the glass on top of the tank.

The glass popped off the upper seal and moved down just enough to loosen up as it struck the bottom o-ring.

I then unscrewed completely and removed the base. The glass was loose and came right off.

I was sure to apply some e-juice to the o-rings before reassembly but find I have to use the stated technique every time I have to take the Melo 2 apart.

The Cleito is built differently than the Melo 2 but maybe this will give you some ideas.

 

[erikbal]

Thanks for the tips. I can't believe no one else has anything to say. Is the cleito not very popular or well liked?

Sent from my VS980 4G using Tapatalk

 

[ScandaLeX]

Thanks for the tips. I can't believe no one else has anything to say. Is the cleito not very popular or well liked?

Sent from my VS980 4G using Tapatalk

If I had one chances are slim I'd be removing the glass. A lot of people have the Cleito so it is a popular tank.

 

[erikbal]

Honestly I couldn't get the coil unscrewed with the glass on. Now with the replacement glass if I unscrew the top cap I can easily remove the glass if I want. I made sure to lubricate the rubber gasket on the base with some juice and I think maybe that helps.

Sent from my VS980 4G using Tapatalk

 

[erikbal]

Oh and so far so good with the .2 ohm coil. Running between 57ish-70w or so and is willing pretty well. Very smooth open airflow and so quick and easy to fill.

Sent from my VS980 4G using Tapatalk

 

[Sil3nt]

Grab by the notches on both sides and wiggle glass back and forth.

 

[Bhoot]

I had crack one tank glass because the beetroots top would not unscrew. I have started applying some Vaseline to the coil top and top tank section. Also found that overfilling even a bit and it leaks. No over fill and top screwed in right, never leaked. Not a leaky tank itself. Bought the coil master tank tweezer tool but that does not tighten it enough. Brilliant tank and 0.4ohm coils.


Sent from my iPhone using Tapatalk

 

[Miata GT]

The worst problem I had with mine was that once the coil came unscrewed with the top, which would have been a larger issue if the tank had been full of juice!