I'm after a tank....
- Thread starter Hotbox147
- Start date
- th_trl_thread_readers 0
- Status
The idea of the 519 hybrid (such as yours) is that it uses any 510 connection atomizer so just about any 510 tank would work on it. FYI, there are some concerns over the safety of the hybrid design so it is worth searching the forum for the issues. My understanding is people can misadjust the atomizer so that the battery is in constant connection leading to it going thermal.
Thanks @HauntedMyst. I have done a lot of research on this mod both before and after buying it. I only use drippers on it atm but I am after a tank such as the aromamizer or something similar. Just wanted to know if anyone on here has this mod and what tank they have/use on the smpl mod before I go out and buy one for it to do what you just stated.
Also granted while any 510 tank would work on there it's best if I have one with a protruding 510 pin. Up until now the only one I have found is the aromamizer. Getting one with a protruding 510 pin would make sure that the negative contact on the tank wouldn't connect with the positive contact on the battery and short it out
The OBS Crius v3 has an adjustable 510 connection.
Details OBS Crius (v3):
Removable stainless steel + glass hybrid 510 drip tip
Top side fill design
Glass tank size: 21mm*25.5mm (D*H)
4ml juice capacity
Juice flow control
Dual posts (quad poles) design for dual coil build
Adjustable airflow control (2 air slits on the AFC ring)
510 threading connection
Adjustable brass centerpin screw
22mm overall diameter
You should still check your connections every time you take the tank off and I would even check it everyday as a part of my routine. If you feel that button get hot take your finger off the fire button asap.
One downside, there are no premade cols for this tank yet, might come out later but for now it's a velocity style deck and you build the coils on that. Has options for dual or single coil.
Details OBS Crius (v3):
Removable stainless steel + glass hybrid 510 drip tip
Top side fill design
Glass tank size: 21mm*25.5mm (D*H)
4ml juice capacity
Juice flow control
Dual posts (quad poles) design for dual coil build
Adjustable airflow control (2 air slits on the AFC ring)
510 threading connection
Adjustable brass centerpin screw
22mm overall diameter
You should still check your connections every time you take the tank off and I would even check it everyday as a part of my routine. If you feel that button get hot take your finger off the fire button asap.
One downside, there are no premade cols for this tank yet, might come out later but for now it's a velocity style deck and you build the coils on that. Has options for dual or single coil.
Orchid. Both clones I own have a good protruding pin, I had to sand one down to thread onto my tesla battery without leaving a gap.
Aqua V2.... remove the SMPL top cap and the base cap of the atty and then you have a a real hybrid 
Aqua V2.... remove the SMPL top cap and the base cap of the atty and then you have a a real hybrid
Uh. The SMPL doesn't have a top cap. I carried a SMPL as a backup when I used the istick40tc. After I got the 60 TC I sold my SMPL on eBay.
Absolutely correct brother. That's why I got a SMPL. One less thing to lose.
Was going to say I did research it a lot before buying it. The 510 is milled directly into the tube @Bunnykiller you just screw your atty in (of course making sure it has a protruding 510 pin) pop the battery in. Making sure it's wrapping is intact completely then screw the firing button into the tube with fingers then give it a pinch with a coin to make sure it's tight.
The Aromamizer or Mutation MT tank are good suggestions. Both mine have a solid positive pin that does not move if squished.
As always with the pinless 510s, Always double check the atties 510. Make sure it protrudes (or else the battery positive with touch the atties positive and ground) Also find a table edge, and push on the attie positive pin. Make sure it does not squish in. Even on non spring loaded pins, they can move if the insulator is squishy.
Press the button firmly, battery pushes up which then pushes on the attie positive pin, if there's any squish it can short out
As always with the pinless 510s, Always double check the atties 510. Make sure it protrudes (or else the battery positive with touch the atties positive and ground) Also find a table edge, and push on the attie positive pin. Make sure it does not squish in. Even on non spring loaded pins, they can move if the insulator is squishy.
Press the button firmly, battery pushes up which then pushes on the attie positive pin, if there's any squish it can short out
It helps to have a spare tank.
The aromamizer, bellus and mt will all work fine, as will the goliath v2 and cthulu.
Is the SMPL 22mm? FYI the aromamizer is 23mm, so it'll hang over your mech if it's 22 even. I typically use the bellus on mechs cause it looks better.
Is the SMPL 22mm? FYI the aromamizer is 23mm, so it'll hang over your mech if it's 22 even. I typically use the bellus on mechs cause it looks better.
The smpl is 22mm if I'm not mistaken. My velocity and royal hunter both sit flush and don't overhang on it so I imagine so. Rather gutted about the aromamizer because I really liked the look of that, overhang would bother me though. I'll look into getting the bellus, thanks @HighPlainsPuffer
It helps to have a spare tank.
I'll drink to that. I have a spare RTA and a spare mod. The last thing o ever want to for me to get on cigarettes again!
Would never recommend a Bellus on a Mech. Because Bellus RTAs are prone to leak through the AFC especially if you too fill.
The Bellus MUST HAVE A VACUUM so finger tight on the top is not good enough.
If you use a Bellus on a mech make sure it is always bottom filled.
I bought an authentic Bellus. I had such high hopes for the Velocity deck. I vaped for about 90 minutes and 1/2 a tank of juice spilled all over my hand and mod.
The term disappointed was an understatement!
- Status
Similar threads
