iPV Mini?

[Major911]

another good choice based on the reviews and your recommendation. thanks

You might check out the kanger sub tank. Even though it's 25mm it doesn't look bad on the ipv mini. You can always use the 22mm beauty ring if you like. IMHO it out performs the Atlantis and has the rebuildable option as well as the stock coils. I think it's the best tank kanger has come out with so far.

 

[kaljo]

Or wait for the mini=22mm RBA or the nano=18mm

Instagram

 

[nelsonm64]

Or wait for the mini=22mm RBA or the nano=18mm

Instagram

now we're talkin'! 22mm ... now it will be a toss up between the Joyetech Delta II and the 22mm Kanger...

 

[jersey girl]

Its working well on the IPV Mini in PWM mode if you want below 11watts and fine in DC-DC mode if you want 11watts or more. Thats with a 1.6ohm coil. A 1.8ohm gives a tiny bit more wiggle room in DC-DC mode if you prefer less than 11watts.

ATM im vaping some Charlie Nobles Commodore Pearry which is thick, 28PG/82VG. This coil is about a week old (over 20ml worth) and still chucking some nice vapor and flavor.

right now I have a lot of liquid (holiday sale) that is 70pg/30vg in pwm mode 8.5W, 2.1 ohm coil (which reads 2.0 on the mini) your juice is much thicker.
Is mine too thin for this tank?

 

[jersey girl]

You might check out the kanger sub tank. Even though it's 25mm it doesn't look bad on the ipv mini. You can always use the 22mm beauty ring if you like. IMHO it out performs the Atlantis and has the rebuildable option as well as the stock coils. I think it's the best tank kanger has come out with so far.

thank you for that suggestion. I don't feel like I am ready to sub-ohm. and truthfully don't want to tinker with coils. I will take a look at it.

What I really am looking for is a good reliable tank that will work well with the mini (and look good). with long lasting stock coils, and adjustable airflow.
just easy refill, get a good vape, and replace a coil once in a while. easiy peasy.

 

[Flt Simulation]

BTW ... Here is a Kanger Mega on top of the iPV Mini:

 

[Ringo®]

Got my replacement mini in today. Unfortunately, same problems as the last one. Crooked 510 and reads .2 low. Going to give up on P4U for a while.

 

[zoiDman]

Got my replacement mini in today. Unfortunately, same problems as the last one. Crooked 510 and reads .2 low. Going to give up on P4U for a while.

That Sucks.

 

[Ringo®]

That Sucks.

It would suck more if it was my only vw mod. Thankfully, I have a bunch. It's not like it doesn't work at all, so I'll rank it as unfortunate. I think P4U should fire everybody but 1 guy in the QC department (leave one so he can tell the new guys what happens when you screw up this bad)

 

[jersey girl]

BTW ... Here is a Kanger Mega on top of the iPV Mini:

that does look good! and I have the silver mini.

 

[jersey girl]

Got my replacement mini in today. Unfortunately, same problems as the last one. Crooked 510 and reads .2 low. Going to give up on P4U for a while.

OMG!!!!! are you sending it back again?

 

[Major911]

thank you for that suggestion. I don't feel like I am ready to sub-ohm. and truthfully don't want to tinker with coils. I will take a look at it.

What I really am looking for is a good reliable tank that will work well with the mini (and look good). with long lasting stock coils, and adjustable airflow.
just easy refill, get a good vape, and replace a coil once in a while. easiy peasy.

No need to sub ohm. They come with a 1.2 ohm coil as well and for me that's even better than the .5 cause I can run at lower watts and save battery and still get a satisfying vape. It's just a beautiful tank, holds a ton of juice, and Vapes smooth as silk with amazing flavor. Comparable to my kayfun's IMHO.

 

[Major911]

;14973507]Got my replacement mini in today. Unfortunately, same problems as the last one. Crooked 510 and reads .2 low. Going to give up on P4U for a while.

Sorry to hear that. I'm still waiting for my replacement to come from asmodus. The board crapped out on mine after 3weeks and the dealer I bought it from didn't want to be bothered with it. Referred me to the warranty company so I had to pay $8.00 service fee up front plus shipping to them. We'll see what happens.

 

[Evi|grin]

right now I have a lot of liquid (holiday sale) that is 70pg/30vg in pwm mode 8.5W, 2.1 ohm coil (which reads 2.0 on the mini) your juice is much thicker.
Is mine too thin for this tank?

I dont think it would be. I just prefer 50/50 or thicker liquids.

 

[Ringo®]

OMG!!!!! are you sending it back again?

Nope. Don't really see a point in wasting the vendors time with this in what I'm fairly certain would be a repeating issue. Like I said, it still works, just not exactly as expected.

 

[Flt Simulation]

Let us know what the Number on it is when it Arrives.

The replacement cap from Elev8 Vapes came in the mail today.

Same number as the original damaged cap ... L0836

 

[nelsonm64]

Got my replacement mini in today. Unfortunately, same problems as the last one. Crooked 510 and reads .2 low. Going to give up on P4U for a while.

my 510 wasn't straight either. I fixed by putting a kayfun on it, screwed it down till it was 2mm from being flush and, cranked on that puppy till it was straight! not for the faint of heart but it worked 100%

 

[aldenf]

Or wait for the mini=22mm RBA or the nano=18mm

Instagram

It was only a matter of time that they released smaller versions of the SubTank. Kanger's plan for the original BPDC head was to make it compatible with all all their BDC attys larger than 14mm. When they scrapped the BPDC, it eliminated the OCC's use in the other clearomizers. I am looking forward to the small devices. Here's hoping they hold more than half a ml!

 

[nopoison]

my 510 wasn't straight either. I fixed by putting a kayfun on it, screwed it down till it was 2mm from being flush and, cranked on that puppy till it was straight! not for the faint of heart but it worked 100%

yep! I actually lessened the tilt on mine by forcing it into a straight position as I slowly screwed the atty in! There is a bit of play when you first start to screw the atty on so thats when I decided to just force it straight as I screwed it in. Its not perfect but better than it was when i first got it.

 

[nelsonm64]

yep! I actually lessened the tilt on mine by forcing it into a straight position as I slowly screwed the atty in! There is a bit of play when you first start to screw the atty on so thats when I decided to just force it straight as I screwed it in. Its not perfect but better than it was when i first got it.

great, glad it worked out for you