Ithaka to stealth without 510 base, need what?

[JCB1]

GG friends,

If i want to use the Ithaka with GG Stealth without the 510 base, I need both the GG SS Connector and Collector tank? And do I need the Full Connector with inside pieces or just SS Connector? And lastly, I'm assuming this set up will allow the 510 pin to screw directly into GG Stealth with out the base for a more flush look?

Thanks in advance!

With kind regards~

 

[Aal_]

Gg full connector with inside pieces, collector tank and an air control ring (unless u use the one that can with Ithaka). It will give a flush look. I will post a pic in a while. However if you got one of the new stealths, the 510 of stealth is not round and will give you flush look that you want.

 

[JCB1]

Thank you aalwani!

Will look for your pics and also consider getting the new Stealth!

 

[Aal_]

Sorry for the quality. The problem with the collector tank is that even if you remove the brass pin (which I did) you will still have a gap since post of Ithaca is long and it pushes ggts pin too much.

On the right is regular stealth.

 

[imeothanasis]

you need this JCB1 my friend and you will not have any gaps

GGTS Full Connector with Collector Tank

GG friends,

If i want to use the Ithaka with GG Stealth without the 510 base, I need both the GG SS Connector and Collector Tank? And do I need the Full Connector with inside pieces or just SS Connector? And lastly, I'm assuming this set up will allow the 510 pin to screw directly into GG Stealth with out the base for a more flush look?

Thanks in advance!

With kind regards~

 

[Aal_]

Imeo this is what i am using in the left picture. Using collector tank on a stealth with ithaka will leave a gap because the ggts pin protrudes more than in the case of Odysseus

 

[imeothanasis]

there is no gap between Ithaka and cap aal. Except you mean the gap that telescope leaves. I dont think JB means that

 

[imeothanasis]

Edit.........Stealth doesnt have a telescope on it, you are right aal. But he can always take off the brass adjustable pin of Ithaka. Can you try it this way and tell me if it still leaves a gap?

 

[Aal_]

Edit.........Stealth doesnt have a telescope on it, you are right aal. But he can always take off the brass adjustable pin of Ithaka. Can you try it this way and tell me if it still leaves a gap?

Already did that IMEO, the picture is without the brass pin

 

[imeothanasis]

Ah, ok aal. So JC just needs a telescope to eliminate that gap

 

[fright88]

Or you could shorten the adjustable pin on the collector tank. Cut it down a little at a time till you loce the gap if you cut to much put the brass adjuster back on ithaka.

 

[justinred]

Or you could shorten the adjustable pin on the collector tank. Cut it down a little at a time till you loce the gap if you cut to much put the brass adjuster back on ithaka.

Still a quarter of an inch gap showing with the collector pin fully pushed in.

 

[Aal_]

Still a quarter of an inch gap showing with the collector pin fully pushed in.

what do you mean? is it with ithaka? because if you push in the pin all the way, it becomes like a stealth cap and it should not leave any gaps

 

[justinred]

what do you mean? is it with ithaka? because if you push in the pin all the way, it becomes like a stealth cap and it should not leave any gaps

I mean just like the ggts setup you did on the 1st page of this thread. With an 18350 battery and even without any atty attached, telescope screwed in maximum, still leaves a gap. So there will still be a gap even if adjustable pin in the collector tank is cut down.

 

[Aal_]

I mean just like the ggts setup you did on the 1st page of this thread. With an 18350 battery and even without any atty attached, telescope screwed in maximum, still leaves a gap. So there will still be a gap even if adjustable pin in the collector tank is cut down.

This is a stealth not a GGTS. No telescope there. No Gap. Rethreader is connected to collector tank.

 

[fright88]

I mean just like the ggts setup you did on the 1st page of this thread. With an 18350 battery and even without any atty attached, telescope screwed in maximum, still leaves a gap. So there will still be a gap even if adjustable pin in the collector tank is cut down.

If you cut the pin inside the collector tank enough there will be no gap. Another alternative is you could take the pin out of the stealth cap (with the plastic piece) and screw it into the collector tank base. I know this works without gaps because I have it setup now.

 

[Aal_]

If you cut the pin inside the collector tank enough there will be no gap. Another alternative is you could take the pin out of the stealth cap (with the plastic piece) and screw it into the collector tank base. I know this works without gaps because I have it setup now.

fright, don't tell me i could screw the same stealth pin to a collector tank!! MAN i never tried this!

 

[fright88]

Lol I just tried it for the purpose of this thread. But now I will keep it in to shorten the length of my full GGTS.

 

[JCB1]

Thanks all!


Juanita

Sent from my iPhone using Tapatalk

 

[thedrpepperdude]

I was able to use this trick, swapping a stealth center pin into a TS connector.
I am using 18650 battery with no telescope.
Bottom tube, rethreader ring, top tube, TS connector(w/stealth pin), collector tank, Ithaka.
This makes for a very solid feel.
It all goes together with no gaps if I leave out the battery spring.
Thanks for the great tip.