kayfun 3.1 help.
- Thread starter nixoahz
- Start date
- th_trl_thread_readers 0
- Status
The 3.1 should only leak out the airhole if the bottom overflow chamber is filled with juice. The bottom can fill up because of over wicking or negative pressure was lost.
Do you keep your atomiser lying on its side at night? That can cause major leakage.
You have to make sure that both wicking ports are covered with juice to maintain the vacuum .I usually store mine upright on a stand. That should prevent any overnight leaking into the chamber .
You have to make sure that both wicking ports are covered with juice to maintain the vacuum .I usually store mine upright on a stand. That should prevent any overnight leaking into the chamber .
Last edited:
Do you cover the airhole while filling? You should if you don't, then catch the threads of top cap, invert and screw it on completely. Or try using the fill port while holding upside down. The fill port is hassle free.
Sent from my Nexus 5 using Tapatalk
Sent from my Nexus 5 using Tapatalk
Last edited:
After you fill the juice from the top, cover the air hole with your finger while you screw on the top. Once the oring makes contact, flip it upside down and take your finger off the air hole, then let all the juice fall down to the top and continue to screw on the top section while it's upside down. If you find juice coming out of the air hole get a tissue, cover the air hole and blow into the drip tip to clear your air hole. Also store it right side up.
Filling just from the top usually what these leaking issues if do it wrongly. I got a kayfun 3.1 too. Fill using the fill hole, never had any leaking issues even if i leave it on the side overnight.
Top filling method thats alot of practise and could sometimes have alot of juice wastage if done wrongly.. Tried that method last time but was only sucessful 2 out of 10 times.
The top filling method is using fill the juices to 3/4 then screw in the top cap in abit and flip it upside down and covering the intake air hole then start tightening the top part.
Last edited:
dun know how to explain, but this video helps great
Tutorial - Kafun type atty mech build - also top fill method - YouTube
Tutorial - Kafun type atty mech build - also top fill method - YouTube
or this....
this will be more appropriate as most of us will face small amount of excess liquid overflow...
Kayfun 3.1 | How to Wick & Fill - Easy! | NO LEAKS NO GURGLING | 2vaped.com - YouTube
this will be more appropriate as most of us will face small amount of excess liquid overflow...
Kayfun 3.1 | How to Wick & Fill - Easy! | NO LEAKS NO GURGLING | 2vaped.com - YouTube
When I get leakage from the air hole after top filling it usually means I over juiced my wick before filling it. You just want to make it a bit wet, not saturate it. The pressure from screwing the cap on even with covering the air hole will still shoot juice up to the wick. You want the wick to still soak up some juice to prevent leaking.
It takes practice but I rarely get any leaks from top filling any more.
It takes practice but I rarely get any leaks from top filling any more.
90% of the time if i have leakage from the air hole, this is the cause. Take the contact screw out from the bottom, and unscrew the bottom justice trap. Clean it out and then refill using the methods described in this thread. Should fix you right up.
I using this method... till now.. only initial overflow...when overturn closing top cap...
I top up again when the juice is half or a quarter full.... no problem....
Juices leaking comes from improper filling and also sometime is due to wicking issues. On initial use of KF, I have it too but after reading and experimenting leaking less occurs
Sometime, when I did not concentrate while filling and talking at the same time leaking occurs but can be easily manage by sucking all the juices out
Also, I had experience it if you over fill the tank, I can't get the wicking wet fast when chain vaping, seems that there isn't some pressure inside to allow juices to follow in, so I empty some out and it became as good
Just try and try you will achieve leaks free soon!
Sent from Gotham City using Tapatalk
Sometime, when I did not concentrate while filling and talking at the same time leaking occurs but can be easily manage by sucking all the juices out
Also, I had experience it if you over fill the tank, I can't get the wicking wet fast when chain vaping, seems that there isn't some pressure inside to allow juices to follow in, so I empty some out and it became as good
Just try and try you will achieve leaks free soon!
Sent from Gotham City using Tapatalk
Last edited:
I find flipping it upside and blowing the juice out of the channel helps a lot.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- Status
Similar threads
