Hello guys, so just ordered a cana modz aka dna30 , and need some advice. I have a kayfun nano and have been building 1-2 ohm on my vamo v5 on 30awg kenthal. I was wondering if anyone here has the same setup (cana modz & kayfun ) and what builds you are running/recommend.. I will also be using a nautilus with the bvc coils in it.. All feedback will be greatly appreciated!
Kayfun nano & Cana modz
- Thread starter WhatupFoo
- Start date
- th_trl_thread_readers 0
- Status
Cana 30w with kayfun lite +
1.5 ohm micro coil, wicked with cotton, running @ 15 watts
1.5 ohm micro coil, wicked with cotton, running @ 15 watts
28g kanthal.
It make good vapor. Good enough for me.
It won't win any cloud chasing competitions BUT that's NOT what kayfuns are made for.
Kayfuns are made for flavor and they deliver! BUT wicked right, you can make good clouds too, just not like you'll get from a well built dripper.
It make good vapor. Good enough for me.
It won't win any cloud chasing competitions BUT that's NOT what kayfuns are made for.Kayfuns are made for flavor and they deliver! BUT wicked right, you can make good clouds too, just not like you'll get from a well built dripper.
No issues with my Cana/clouper v2- I run a keyfun clone with it using 30 gauge @1.3 to 1.7 ohms - I use the Cana/clouper as my beater mod - no regrets purchasing the clone - hope this helps!
Best regards and vape safe friends!
Tony
Best regards and vape safe friends!
Tony
Last edited:
I've had it a little over two months and I haven't had any issues with mine either. It's my all day, everyday vape gear. I have a ton of mechanical mods, MVP 2.0, Vamo v5 and they are all collecting dust because of the Cana 30w. I do carry a mech with a dripper as a back up though.
Running a Cana Modz 30, with Kayfun lite v2 plus clone..my build is around 1.5.. I'm using twisted 32 gauge wire single coil setup (cause i have ton of it during my Kanger coil rebuilding days). I think most people use 28 or 30 gauge wire for their setups.
Im thinking of grabbing a mvp later my vamo is dying the threads are all messed up , i really dont think im a dripper , havent tried but doesnt interest me at the moment.
Kayfun lite and nano are similar right just the tank is bigger on the lite? But building coils is the same right?
It does ok with the kayfun and the nautilus but im sure i can get the best out of the kayfun on the cana, anyways its getting retired once get the cana [emoji2]
I think I got one (Vamo) that was made at closing on a Friday. Just junk from the word go....
Prices will be dropping faster than your head can spin...everybody is on wattage trip these days (50 to 100 watts)...so you might want to even look at Cana mod 30 or wait for Innokin's next revision of box mod. You never know when you might need that extra power for RDA, or extra boost of power for that Kayun, etc...I've hit 15 to 17 watts on my builds for my Kayun. It really depends on what e-juice I'm using etc.
So excited.... Delivery said by Sat but tracked it today and its says should be out for delivery today, anyways i have 26 and 30 awg kenthal , which size should i use and how many wraps for the kayfun? I want to get a warmer vape and the most clouds out of it.
The nano kit just gives it a smaller height and a smaller liquid capacity - deck size remains the same - and your coil build stays the same.
From what I have - the only diff is that the outer rings are smaller in height...
*** not my picture - it's from a foreign site here - hope no one minds - mods/ op poster from foreign site etc hope u guys don't mind - here's linkage ****http://www.e-papierosy-forum[/url] DOT pl/kayfun-nano-body-kit-t55356.html***. Please take down linkage if it's not allowed
Hope this helps
Best regards and please vape safe friends
Tonyc
I use 28g but try this link Coil wrapping | Steam Engine | free vaping calculators you can plug in the different wire sizes and jig info and it will give you all the info you need. It's pretty accurate too.
- Status
Similar threads
- Locked