My 6v mod with HV atty

[drewk302]

Here is a pic of my 6v mod. Its a 501 fitting with 501-801 adapter. I had it running as high as 8v, at 8v it was very hot, I burned juice so fast and the flavor was hot. Now I have it running a 6v. It is pretty good, nice smooth vapor, still eats juice fast ( I direct drip ). The mouth piece that comes with the hv atty is so flat, and I taste the plastic some. Other than that it performs well. I also have the 3.7v box mod running a lr atty. That 3.7 is awesome, performs great, I will say though, I like the bigger diameter opening on the 6v HV atty.

http://www.flickr.com/photos/59411845@N03/5436844711/

 

[alisab]

What pv and attys (brand names and ohms) are you using? I vape at 6 volts mostly and I usually don't have a burnt juice taste, but I do sometimes. Some juices just can't be vaped at 6 volts. 8 volts! I just can't imagine!

 

[doots]

pretty nice tube mod. big switch.

 

[drewk302]

I am using hv atty from ikenvape its like 3.5ohms the pv's are in the pic. The juice is bekang brand I believe. My local tattoo shop sells the juice, taste great and pretty good vapor!.

The switch is a little big, I had a smaller one but it broke so I used one that I had.

 

[Para]

I had it running as high as 8v

What batteries/setup produces 8v?

 

[alisab]

I also use the 801 hv atty from ikenvape a lot. It has a very forgiving dripping ability and also tends not to get hot - it gives a pretty full "vape" too. The dekang juices are pretty thin - I think it may be 100% PG and that could be part of the reason it burns sometimes and eats juice. But dekang is cheap juice and you like it so wth?! BTW I vape without any tip on the 801, they call it tailpiping I think - it's just easier for me and the thing is pretty long already.

 

[drewk302]

Yea I usually dont use the tip, I dont like it.The juice I have is 100% vg, pg I dont like.
To get 8v I was using 2 15270's rated at 3.7v each but fully charged I get consistant 8v. I also put them in my unvoltage regulated setup.

 

[WillyB]

What pv and attys (brand names and ohms) are you using? I vape at 6 volts mostly and I usually don't have a burnt juice taste, but I do sometimes. Some juices just can't be vaped at 6 volts. 8 volts! I just can't imagine!

And what do you use to get '6V"?

 

[Para]

Yea I usually dont use the tip, I dont like it.The juice I have is 100% vg, pg I dont like.
To get 8v I was using 2 15270's rated at 3.7v each but fully charged I get consistant 8v. I also put them in my unvoltage regulated setup.

Have you metered them after a half hour and after an hour?

 

[drewk302]

And what do you use to get '6V"?

2 15720's rated at 3.0v each hold consisant 6v

Have you metered them after a half hour and after an hour?

I have, several times lowest it gets is around 7.8v seems they are a little under rated. pretty powerful battys.

 

[drewk302]

Side note, the tip that comes with the hv atty, once it gets wet around the edges from fluid it falls off very easy making i hard to use in your pocket. I went to the store and brought it with me it fell off several times, and then i didnt even know it but i lost it. Vapes so much better with no tip but, can make travel use messy. grrrr