need advice on device I am using

[bojacker]

I am using a spinner and I am wondering if I am doing something wrong. I take long slow draws and seems my Te bottom coil head lasts about a day and then I have to use a new one. Getting expensive
I am hoping someone can advise me....am I doing something wrong, or is there a better head available that will fit spinner battery?

 

[Katya]

What is Te? What resistance is your coil and what voltage is your Spinner set to?

Oh, welcome to ECF!

 

[Scarey]

You can do that. Just don't throw it away. Toss it in a glass of vodka overnight. The next day, rinse it out well, and toss that day's head in the vodka, and use a third head. Let the first head dry overnight. Next day, toss head 3 in vodka, rinse and dry head 2, use head 1. Run at least those 3 heads in rotation like that, and they should last you a very long time.

 

[Michael Pham]

I'm guessing your meaning the kanger T3? If so have you tried removing the flavor wicks? Sometimes it just chokes your wick and it seems like it's burning but in reality your just getting a bad dry hit.

 

[dice57]

Yeah, wouldn't recommend removing flavor wicks, that way leads to big time flooding issues. Unless you are vaping 100% VG. The most common mistake made with a new vaper, is to not allow enough time for the juice to fully saturate the wick before the first vape. This can burn the wick, reducing it's wicking properties and shorten it life span. When I used a knager product I always let a new head soak for about 15 minutes before the fist vape. When I did this, I could vape up to 3 weeks before cleaning or replacing was needed. Also rinsing out your tank ever other fill will help too.

 

[Amberina]

Make sure you let your juice sit in the tank for at least 10 min before you start to vape it for the first time after you replace the coil. Even though the wicks on those are very small, they still need time to get completely saturated. I started off with the t3's also and I had burnt taste issues until I realized I had to let it sit for a while. You can save the old ones. Just do what Scarey said to do. I have done this too and it has saved quite a few coil heads!

Good Luck!!

 

[bojacker]

The TE bottom coil clearomizer that fits Spinner 1300mah. You can buy the replacement coil heads separately. I use it turned up 4.3V. I asked the vendor and that is what they suggested.

 

[bojacker]

no it is a Volts Spinner and I do not believe there is a wick. I purchased from Smokeless Image, it is their new one.

 

[sludgeroo]

The resistance on your head will determine if 4.3 volts is necessary.

If it's a 1.5 to 1.8 head 4.3v May be a little much.

Sent from my VS980 4G using Tapatalk

 

[bojacker]

I will try waiting to vape. I have about 6 new tanks so I always have fresh clean ones.

 

[bojacker]

no Volts new Spinner with X2- Te clearomizer bottom coil.

 

[bojacker]

Thank you I will try this as I have about 30 that I haven't discarded yet.

 

[bojacker]

The vendor suggest for warm best flavor and vape to crank all the way, if I get burnt taste with some flavors try going down. I have experimented with it but still clogs up and just dies on me.

 

[ijmunoz]

I have had great luck with my itaste2 and my protank 2. I recommend them.

 

[bojacker]

Te is the new bottom coil head designed for their new Volts Spinner. it also will fit their X2

 

[pufZeppelin]

The TE bottom coil clearomizer that fits Spinner 1300mah. You can buy the replacement coil heads separately.
I use it turned up 4.3V. I asked the vendor and that is what they suggested.

no it is a Volts Spinner and I do not believe there is a wick. I purchased from Smokeless Image, it is their new one.

Te is the new bottom coil head designed for their new Volts Spinner. it also will fit their X2

Hi bojacker. welcome to ECF

I think if you look better you'll see it's not TE but T3--
which from looking at SI site is just a Kanger T3 (the old one)
newer version would be T3S, but SI page does not distinguish the diff...
(diff is coil separates from base on newer ones making it cheaper to replace)

3.8 volts is a bit high TO START -IMO- start low, then work up to what tastes good to you...

coils only last a day, why ? taste bad (burnt), no vapor, stop working ?
not enuff info of what you mean, what the actual problem is...

what is the Ω of the coils you are using ?
SI has no option for coil Ω ??



- Kanger T3s Rebuildable Clearomizer 2.5ohm - Purple

- Kanger eVod Base Replacement

- Smokeless Image | The Best Electronic Cigarette

- Kanger T3s/Mini T3s/MT3s

well let us know how you get along...

Vape≈Happy

 

[bojacker]

You are right is it called T3 Problem I have they stop working, and sometimes before they stop, they will gurgle and less vape when they start wearing down. When they are new they are awesome. Maybe I will try Kanger T3s...I read on SI that theirs was one only compatible with their Spinner. Yes the heads are replaceable and cheap at 2.99 ea. but they don't last as long as I think they should , I could be wrong but I'd say 2 tanks they start wearing down is not very good. I have reordered around 30 so far and was hoping someway to clean or find a better alternate. I am getting lots of ideas and feed backs on here from folks like yourself and appreciate all your help. Thanks.

 

[pufZeppelin]

You are right is it called T3 Problem I have they stop working, and sometimes before they stop, they will gurgle and less vape when they start wearing down. When they are new they are awesome. Maybe I will try Kanger T3s...I read on SI that theirs was one only compatible with their Spinner.

Yes the heads are replaceable and cheap at 2.99 ea. but they don't last as long as I think they should ,

I could be wrong but I'd say 2 tanks they start wearing down is not very good. I have reordered around 30 so far and was hoping someway to clean or find a better alternate. I am getting lots of ideas and feed backs on here from folks like yourself and appreciate all your help. Thanks.

so you unscrew the BASE from the plastic tank
now with base in hand--then can you Unscrew the "coil" out of the base ??

if it is one assembly (coil WON'T screw out) then it is the old T3
and you can get a new style base or just buy the whole new T3S
(as per above links)


if I am not mistaken, your Volt Spinner has the standard popular ego threads (do you know?)

- Kanger T3s/Mini T3s/MT3s is cheaper

 

[Katya]

No it doesn't! Volt is kr808D-1 threaded--that's the problem.

However, those coil heads can be cleaned. I just soak them in PGA (cheap vodka or denture cleaning tablets work well too) for a couple of hours!

 

[madqatter]

The vendor suggest for warm best flavor and vape to crank all the way, if I get burnt taste with some flavors try going down.

This is pretty much backwards. Start low and work your way up to good vapor and flavor.