Need More Vanilla

Status
Not open for further replies.

binks00

Full Member
Jul 28, 2014
26
7
lehigh valley
I want more flavor and vapor but get dry hits above 14 Watts. I've tried 3 different vanillas, some 50/50 others 70/30. Is this just the nature of vanilla?

Setup
dna 30
kayfun
Kanthal 26 ga wire with 2mm coil at 1.1 ohm
Cellucotton wick with perfect legnth and placement

I have decent vapor now but want as much as I can get with other juices at 18+ watts.
 

Cullin Kin

Ultra Member
ECF Veteran
Verified Member
Jun 28, 2014
2,746
3,449
The 3Oh!3, Colorado
www.youtube.com
Check out Nicoticket's Frenilla, they specifically test their juices at high wattages on regulated mods and low resistances on mechanicals to make sure it doesn't scorch. Plus, I've heard it tastes absolutely amazing.

I believe your wick is what is causing the problem. If you wick right, you can Vape 100% VG juice a lot higher than 14 Watts. Try wrapping your coil on a 1/8" drill bit, there's a tutorial on this site on this amazing build that you can Vape any juice at high wattages and never get a dry hit.

Edit: Here you go: http://www.e-cigarette-forum.com/fo...ystems/532652-kayfun-build-100-vg-vaping.html

Try that build first. I did it the other night and it is truly amazing.
 
Last edited:

AlbertCH

Full Member
Aug 12, 2014
10
12
Switzerland
Albert - my coil is 8 wraps... so probably about 4 mm long. Could I just use 4-5 wraps and run it at a lower resistance?

Considering the airhole on Kayfuns is only 2 mm wide, I do think it would be better to shorten your coil, to make sure the entire coil stays within the airflow. Either by doing less wraps or by using higher gauge wire.
 

Cullin Kin

Ultra Member
ECF Veteran
Verified Member
Jun 28, 2014
2,746
3,449
The 3Oh!3, Colorado
www.youtube.com
I have the same issues with frenilla. Cullin - ive already subscribed to that thread but I've only tried 2mm coils, I'll have to try 3mm. Albert - my coil is 8 wraps... so probably about 4 mm long. Could I just use 4-5 wraps and run it at a lower resistance?

I do 8 wraps on a 1/8" screwdriver (3.175mm) with 26 gauge kanthal and don't have an issue with any juice at all. It comes in right around 1.0-1.1 Ohms. No matter how hard I try, I can't get a dry hit, not even at 30W. This includes the French Vanilla juice I use.

Shorten coil with less wraps. I can't wait to try. What is the minimum resistance for a kayfun and/or dna?

There isn't one for the Kayfun but you have to remember, the Kayfun can only wick/feed juice so fast. Obviously don't exceed your batteries limits but I see people vaping Kayfun's at 0.5 Ohms and some even at 0.3 Ohms. The lowest resistance a DNA 30 can handle is 0.3 Ohms. Going that low is counter productive though and you may notice that it doesn't work nearly as well as a 0.8 build at 30W.

Try the build above, 8 wraps on a 1/8" (3.175mm) post with 26 gauge kanthal. You won't be disappointed. I'm vaping it at 23.5W on a DNA 30 with a 100%VG French Vanilla/Vanilla Cupcake blend and it's delicious. The vapor is great as well.
 
Last edited:

binks00

Full Member
Jul 28, 2014
26
7
lehigh valley
I just found out I had a loose ground wire on my dna 30 which didn't help matters. That's squared away now and I'm currently running 5-6 wraps @1/8 inch. Good results with strawberry but I did not try vanilla yet.

Thanks for the advise, Cullin. I'll try the 8 wrap of 26 gauge on a 1/8 in. next build. It may be a couple days yet since I just got a magma yesterday. :)
 

GPC2012

ECF Guru
ECF Veteran
Verified Member
Feb 12, 2014
30,681
39,743
Reedley Ca
I want more flavor and vapor but get dry hits above 14 Watts. I've tried 3 different vanillas, some 50/50 others 70/30. Is this just the nature of vanilla?

Setup
DNA 30
Kayfun
Kanthal 26 ga wire with 2mm coil at 1.1 ohm
Cellucotton wick with perfect legnth and placement

I have decent vapor now but want as much as I can get with other juices at 18+ watts.

Custard Assault, Bionice Vapors. JC can customize it for you however you want it.

E-Juice – Bionic Vapor
 

windyman

Moved On
Aug 14, 2014
0
0
boston mass usa
  • Deleted by retired1
  • Reason: Unregistered Supplier
Status
Not open for further replies.

Users who are viewing this thread