New Arrival: 1.2ml Boge 510D XXL 1.4ml Cartomizers

[newsunshine]

5pc 1.4ml Boge 510D XXL Soft Cap Empty Cartomizer(2 colors) [510D XXL] - $6.00

Tube size:Length 45mm;Diameter:9.2mm
Resistance: Regular(2.7-3.1 ohm) /LR(Low Resistance 2.0-2.2ohm)
Volume: 1.4ml (350-380 mouthfuls)

 

[andyman97]

Awesome! These are the new ones that fit dual coil tanks, right?

 

[MUKHRFF]

Awesome! These are the new ones that fit dual coil tanks, right?

its fit or no

 

[newsunshine]

its fit or no

They do fit DCT in length. but they are not pre-dotted or with flange.

We do not suggest you to use them directly with 510DCT.

 

[MUKHRFF]

They do fit DCT in length. but they are not pre-dotted or with flange.

We do not suggest you to use them directly with 510DCT.

i already purched it

but pls try to send before saturday

i will pm you my order number

maybe i can dotted it

but who have idea about flange

what i can do for that

 

[jteezy]

I haven't tried it myself but I saw someone suggest using a very thin washer and a 510 shorty extension to act as a flange.

 

[MUKHRFF]

I haven't tried it myself but I saw someone suggest using a very thin washer and a 510 shorty extension to act as a flange.

thank you

thats good

i will try that when i recive my item

and i will check more about any idea also

--

 

[andyman97]

They do fit DCT in length. but they are not pre-dotted or with flange.

We do not suggest you to use them directly with 510DCT.

Are you certain they're long enough? I don't want to be the guinea pig to find out they aren't long enough...

 

[newsunshine]

Are you certain they're long enough? I don't want to be the guinea pig to find out they aren't long enough...

yes. their tubes are the same long as tubes of cartomizers for 510DCT.

 

[Sad Society]

I checked out the measurements, and it looks like they will fit the DCT. As far as the prepunch. I could do that myself. And for the flange. I've read about people not have any problems about leaking, I don't think they necessarily have to be flanged.

 

[djej]

Flange is more for slip down prevention. It's just a precautionary measure, not completely necessary. The only way the flange helps with "leaking" would be if the tank slipped down too much, but it doesn't help seal it any better.

If you're using it on an ego, you can buy this....

eGo Chrome Cone for the 5 mL Dual Coil Tank Cartromizer

It would give the tank something to rest on, preventing it from slipping down, similar to what the flange is doing. It would work on the 3.5ml tanks too, it would just be a bigger around the tank base.

Heck, even this would work for all size tanks....

http://www.madvapes.com/eGo-Chrome-Cone-for-the-35-mL-Dual-Coil-Tank-Cartromizer_p_3438.html

 

[donnah]

Awesome!! I've been waiting!! Wouldn't it be nice if someone did a co-op!

 

[wwturner]

As far as the flange goes, you don't need it. Just put it in the tank upside-down. Be VERY careful if you're thinking of punching it, because it you make the carto bluge too much when punching it, you WILL have problems with leakage. I personally just cut 1 slot in mine and they do fine. When putting the carto in, try to use a drip-tip that fits flush with the mouth of the carto and fits all the way through the tank, to make it easier on your inner seals.

Hope that helps.

 

[newsunshine]

As far as the flange goes, you don't need it. Just put it in the tank upside-down. Be VERY careful if you're thinking of punching it, because it you make the carto bluge too much when punching it, you WILL have problems with leakage. I personally just cut 1 slot in mine and they do fine. When putting the carto in, try to use a drip-tip that fits flush with the mouth of the carto and fits all the way through the tank, to make it easier on your inner seals.

Hope that helps.

It helps.

But I do not recommend it unless it is a pleasure for you to punch it.

 

[wwturner]

New sunshine, where in this post did I suggest TO punch them??? If you read again, you will see that I CUT a SLOT in the ones I use.

Just out of curiosity.... Do you actually pay attention when you read these posts??

 

[melloyello]

now thats a nice way of saying "please read my post again".

 

[djej]

The only concern with the boges in a DCT would be that the smoktech tanks are a "little" bit looser than your average tank. The smoktech cartos slide around just a hair easier than your standard tank setup IMO. That's not to say the boges won't work. They will certainly fit, they MAY just be a hair slippier than usual. The flange on the smoktechs gives the tank something to rest on in case it wants to slide down. Of course the boges diameter could be a micrometer thicker and all this might not even be an issue. I guess we'll find out when someone gets some and puts it in.

 

[Sad Society]

The only concern with the boges in a DCT would be that the smoktech tanks are a "little" bit looser than your average tank. The smoktech cartos slide around just a hair easier than your standard tank setup IMO. That's not to say the boges won't work. They will certainly fit, they MAY just be a hair slippier than usual. The flange on the smoktechs gives the tank something to rest on in case it wants to slide down. Of course the boges diameter could be a micrometer thicker and all this might not even be an issue. I guess we'll find out when someone gets some and puts it in.

Yes, I was wondering this myself, since I have a DCT. I haven't ordered these yet, but I will on my next order.

I also have a Mom & Pop Sub tank if the DCT doesn't work.

 

[Bizrad8381]

I've cut down a Smoktech DCT to fit a standard Boge and it is one of my 2 daily use tanks the fit is not loose at all it doesn't slide around at all. So it shouldn't be an issue.

 

[TopCookie]

Punching them yourself is easy, and they work super well in the DCT tanks - MUCH better than the dual coil Smok cartos...