New Product Releases at SmokTek.com

[JustinUSF]

This thread will be updated for each new product that is made available on smoktek.com

 

[JustinUSF]

Now available at smoktek.com: Smok Zmax MINI Stainless and Chrome

The new ZMAX MINI Advanced Personal Vaporizer is smaller sized, but powerful, reliable, full featured and very well built just like its cousin the ZMAX. With this new version, Voltage or Wattage is variable 3-6 volts or 3-15 watts respectively, using a single 18350 IMR battery. Check atomizer/carto resistance and battery voltage too! Optional extenders for running 18500 and 18650's will be here soon.

The new Rev. 2 Zmax has one extra menu item (8) which enables you to switch between RMS and mean value voltage monitoring. The RMS mode is more accurate because it samples the output Voltage repeatedly while it is powering an atomizer or cartomizer. It is with these measurements that it is able to adjust for heat related Voltage drift.

 

[JustinUSF]

Innokin iTaste VV 3.0 Full Kit, Variable Voltage/Wattage



The iTaste VV v3.0 is a microprocessor controlled variable-voltage/variable-wattage (VV/VW) personal vaporizer that lets you adjust the voltage or wattage in seconds with just a few button presses. It's quick and easy! Full featured and slim sized, this is perfect for beginners and advanced users.


Features:
Variable Voltage:
voltage can be adjusted from 3.3 – 5.0 volts in .1 volt increments.
Variable Wattage:
Wattage can be adjusted from 6.0 – 11.0 W in .5 watts increments.
Ohms meter :
Resistive Load Detection.
Puff Counter:
The puff counter will record how many puffs you have taken. The records will be cleared when the device is turned off.
Short Circuit/Atomizer Protection:
Short Circuit/Atomizer Protection helps protect the iTaste VV against faulty atomizers.
Over-Discharge Protection:
The iTaste VV monitors the battery voltage and will automatically turn off when the battery is discharged.

Passthrough:
The iTaste VV is charged through a Micro USB Port. You can recharge it with any standard Micro USB cable. It can also work as a pass-through device for simultaneous vaping and charging.

Full Kit Includes:
1x iTasteVV (V3.0) 800mAh Polymer Li-ion Intelligent Rechargeable Battery
1x iTaste Retractable Micro USB Cable
1x USB A/C Power Charger Adapter 110V/220V
1x Instruction Manual
1x iTaste VV ( V3.0) gift box package
5x iClear16 Dual Coil Clearomizers - 2.1 ohm (empty /blank )

 

[JustinUSF]

[h=1]Kamry KTS+ Telescoping Mechanical Mod[/h]

Simple and reliable side button design with flat top. Can be fully disassembled for cleaning. The KTS mechanical APV accepts 18350, 18500 and 18650 protected and IMR batteries. This unit works perfectly with the KICK and is machined extremely well.


The mechanical fire button is located at the base of the unit and is quite comfortable to use. It also has a knurled nut to lock it in place so the unit does not accidentally fire.


This device includes a Vape Safety Fuse.


Never use non-rechargeable batteries in this or any other e-cig device! Only use the recommended batteries for this unit, it's for your safety.

 

[JustinUSF]

[h=1]The Telescoping Natural by SmokTech - Mechanical Side Button Mod - Stainless (body only)[/h]

The Natural Telescoping mechanical APV accepts 18350 thru 18650 protected and IMR batteries. This simple and reliable side button design has 1 tube that can be screwed to any length to accommodate the different sized batteries. It works perfectly with the KICK w/18490/500. It is machined extremely well with polished stainless finish.


The mechanical fire button is located at the bottom side of the unit and is quite comfortable to use, requiring little pressure to activate it. It also has a knurled nut to lock it in place so the unit does not accidentally fire.


Never use non-rechargeable batteries in this or any other e-cig device! Only use the recommended batteries for this unit, it's for your safety.

 

[zoiDman]

Cool...

 

[JustinUSF]

ZMAX Telescoping Variable Power (adjustable wattage) VV APV, Rev.2 - Stainless


The new ZMAX Advanced Personal Vaporizer is sleek, powerful, reliable, full featured and very well built just like its cousin the VMAX. With this new version, Voltage or Wattage is variable 3-6 volts or 3-15 watts respectively, using a single 18350, 18500, 18650 or two 18350 IMR batteries, (all available separately). Check atomizer/carto resistance and battery voltage too! The Telescoping design allows for different length batteries.


The new Rev. 2 Zmax has one extra menu item (8) which enables you to switch between RMS and mean value voltage monitoring. The RMS mode is more accurate because it samples the output Voltage repeatedly while it is powering an atomizer or cartomizer. It is with these measurements that it is able to adjust for heat related Voltage drift.


With it's 4 Amp output, it is sure to rock whatever device you want to run on it. This version has a blue button and blue LED display that can be turned off. ZMax has the native eGo/510 connection so it will run the Vision eGo Clearomizers, CE4/5 and other eGo devices without adapters. Run 808 devices as well with a 510-808 adapter.


It will work with flat or button top IMR's and protected Li-Ion batteries.


Never use non-rechargeable batteries in this or any other e-cig device! Only use the recommended batteries for this unit, it's for your safety.

Choose the Make It a Kit option to get batteries and a charger at a discounted price.

Menu:

1. Uu- Voltage up
2. Ud- Voltage down
3. So- Standby / on/off
4. Uc- Battery voltage check
5. Ds- Display change / Resistance Ω/Voltage output/Voltage under load 'live'
​

Do - Display atomizer/cartomizer output voltage
Du - Display battery output voltage
Dr - Display atomizer/cartomizer resistance
​

6. Lo- LED on/off
7. Up- Voltage power (Wattage setting)
​

Po - Constant power (wattage) operation​

Uo - Constant voltage operation​

8. Change voltage calculation method, RMS or MEAn calculation​

RMS - More accurate (preferred), looks like ANS on screen
MEA - Older method used by V/Zmax (hotter), looks like NEA on screen
​

In the event of a fault, the following error codes may appear on your ZMAX device:
LOR - Atomizer/cartomizer resistance is too low
LOU - Battery voltage is too low, replace or charge battery
WSC - Short circuit in faulty atomizer/cartomizer​

 

[JustinUSF]

[h=1] Kanger ProTank-II, 2.5 ml Bottom Coil Clearomizer (BCC)[/h]The first glass tank bottom coil clearomizer! Use any juice without damaging the tank. Great new design with removable tip, easy to fill and simple to replace the coil. The Kanger ProTank-II offers the same great features and performance as the Kanger eVod Clearomizers but with higher capacity and a glass tank!


The Protank-II is 510 threaded and will work on all 510 threaded devices and Mod's without the need for an adapter. It also comes with a matching Ego Cone cover for Ego batteries.


Features:

• Replaceable Coil Heads
• Bottom Coil for better performance from your e-liquid
• Pyrex Glass Tank for protection from harsh liquids
• Capacity is 2.5ml+.
• Comes with 1.8 and 2.2 ohm coils

Includes:

• 1 ProTank
• 1 ProTank Base
• 2 ProTank Coils (1.8, 2.2 ohms)
• 1 ProTank eGo Cone cover.
• 1 Nice packing box to store the tank when not in use.

Dimensions: 2-11/16"L x 3/4"D


Please note: Due to the nature of cartomizers, we cannot offer warranty, exchange or returns except if DOA.

 

[JustinUSF]

[h=1]eFest LUC Multi-function Smart Charger with Car Adapter [/h]

[h=1]Features:

• Mini LCD screen displays precise voltage and battery capacity level
• Each charging channel has independent display of charge status
• Automatically adjust discharge current to charge batteries of different sizes
• Over-discharge Protection
• Over-voltage Protection
• Short-circuit Protection
• Reverse Polarity Protection.
• Automatically stops when batteries are fully charged
• DC Wide Voltage (12-24V) Charging Mode
• Dual battery bays can charge 10440, 16340, 14500, 14650, 17500, 17670, 18350, 18490, 18500, 18650, 18700, 22650, 26500 and 26650 lithium batteries (no spacers needed)

The LUC charger will change between 500mA or 1000mA current depending on the size of the batteries.

It will automatically change to:
500mA for 10440, 16340, 14500, 18350, 18500 and 17500 batteries

or 1000mA for 17670, 18650, 18700, 26500, 26650 and 22650 batteries. In 1000mA mode, the LUC will charge batteries at about twice the speed of the Trustfire Multifunctional Charger TR-001 (500mA)

CV is 4.23V.

When the LCD displays ‘Er’(short for Error), the charger will stop charging automatically. This occurs when battery voltage goes below 2V within 5 seconds, the “Er” mark on the LCD screen will disappear once the battery is removed from the charger.

[/h]
Note: Do not mix different types of batteries or different capacity of batteries when charging. NEVER attempt to charge a non-rechargeable battery!

 

[JustinUSF]

[h=1]New Innokin iTaste MVP 2.0 2600mAh Box APV Kit - Variable Volt/Watt[/h] The new Innokin iTaste MVP 2.0 is a variable voltage or wattage box style VV mod featuring long lasting 2600 mAh battery, outstanding build-quality and excellent performance. The iTaste MVP lets you adjust voltages from 3.3 volts to 5 volts or 6-11 watts and comes with one of the most powerful batteries to be featured in a device. It's built-in lithium-ion polymer 2600 mAh also works like a power bank, so it will charge any USB or micro USB device as well as an iphone or ipad. The iTaste MVP uses a pass-through charging system, which means you can charge and vape at the same time. MVP stands for “mobile variable power”. In my opinion, the iTaste MVP is also the “most valuable player” in all Innokin products. Innokin iTaste MVP Features: Compatible with iClear 16/30, CE4, CE5, eGo, VIVI NOVA, 510, Kanger) Operating Volt adjustable (3.3-5.0 Volts in .1 volt increments) Operating Wattage adjustable (6.0-11.0 Watts in .5 watt increments) Puff counter 2600 mAh Polymer li-ion rechargeable battery Portable power source for electronic products Battery capacity display ON/OFF safety switch Passthrough capability Standard Micro & 2.0 USB Socket Short circuit /atomizer protection 3 Amp current limit Over-discharge protection Remembers last set voltage or wattage when the battery is turned off / on. Built-in blue 3 digit display : Display shows Ohms meter, Voltage /Wattage setting, number of puffs taken since last time the battery was turned off. Innokin ITaste MVP Variable Voltage Kit Includes: 1x iTaste MVP 2.0 2x dual coil XL Clearomizers (Innokin iClear16) 1x slim beauty ring (use with Clearomizers, tanks, Vivi Nova, etc.) 1x USB cable/multi-usb adapter 1x transparent carrying case 1x mini-manual * Note- The MVP is compatible with most CE4/Vision style clearomizers AND the Kanger T2 and T3 thanks to the inclusion of outside eGo threading on the newer units.

 

[JustinUSF]

[h=1]Sigelei ZMAX Telescope Variable Power (adjustable wattage) VV APV, Rev.3 Flat Top - Stainless [/h]The ZMAX TELESCOPE V3 Advanced Personal Vaporizer by Sigelei is sleek, powerful, reliable, full featured and very well built. With this new device, Voltage or Wattage is variable 3-6 volts or 3-15 watts respectively, using a single 18350, 18500, 18650 or two 18350 IMR batteries with the included extender cap. Check atomizer/carto resistance and battery voltage too!


Rev. 3 Zmax has a menu item (#8) which enables you to switch between RMS and mean value voltage monitoring. The RMS mode is more accurate because it samples the output voltage repeatedly while it is powering an atomizer or cartomizer. It is with these measurements that it is able to adjust for heat related Voltage drift.


With it's 4 Amp output, it is sure to rock whatever device you want to run on it.


This version is a flat top design and has a non-lighted clear button and very easy to read 2 line OLED display that can be turned off. It has the native eGo/510 connection with outside threads so it will run Kanger products as well as the Vision eGo Clearomizers, CE4/5 and other eGo devices without adapters. Run 808 devices as well with a 510-808 adapter.


The ZMAX requires two high power 18350 IMR batteries, and an extender cap which are included in this kit. It can also run one 18350 IMR, 18500 IMR or 18650 IMR battery. It will work with flat or button top IMR's and protected Li-Ion 18650 batteries.


Never use non-rechargeable batteries in this or any other e-cig device! Only use the recommended batteries for this unit, it's for your safety.


The ZMAX has an 8 feature menu which is accessed by pressing the fire button 3 times.


Menu order:

1. Out/On. Turns the device on or off.
2. Power/Voltage up. Raises the power or voltage up.
3. Power/Voltage Down. Lowers the power or voltage.
4. Battery Voltage. Shows remaining battery voltage.
5. LCD Display. Change what is diplayed on your screen during use. Resistance, Battery Voltage, or Output power/voltage
6. LCD on/off. Turns the LCD screen on or off during use.
7. Power / Voltage setting. Allows you to set the output to power(watts) or Voltage.
8. RMS & Mean Setting. Allows you to use RMS or Mean output for Power/Voltage. (RMS being the more accurate)

The Sigelei Telescope Zmax includes the following:

• 1 Stainless Zmax Body
• 1 Attractive gift box
• 2 Bottom Caps for 18650 or 18350 batteries

We also carry the Chrome Sigelei ZMAX, check it out!

 

[JustinUSF]

[h=1]Stainless Steel Woven Mesh Type 316 for rebuildable atomizers[/h]This is high quality, corrosion resistant stainless type 316 wire cloth woven steel mesh. Available in 400x400, 450x450 and 500x500.
For use in rebuildable atomizers as SS Mesh Wick. This works well with the phoenix or other Genesis style rebuildable atomizers. Many users prefer SS Mesh because of it's ability to resist burning and scorching.
Sold in 3" x 4" segments (aproximate). This will allow you to make 4 or more SS Mesh Wicks.
This item is for experienced users only!
DIY atomizers may pose risk of injury if you do not know what you are doing.
Use at your own risk, please learn about rebuilding before attempting to use.
No warranty.


[h=1]Kanthal A-1 resistance wire for rebuildable atomizers, 32ft spool, various gauges[/h]Kanthal A-1 resistance wire Maximum continuous temp- 2550 degrees F
Wire Gauge- 28 AWG Resistance- 5.6 ohm/ft 16.8 ohm/m. Wire Diameter- 0.32 mm.
Wire Gauge- 30 AWG Resistance- 8.3 ohm/ft 24.9 ohm/m. Wire Diameter- 0.26 mm.
Wire Gauge- 32 AWG Resistance- 14.53 ohm/ft 43.6 ohm/m. Wire Diameter- 0.008" / 0.20 mm.
Wire Gauge- 34 AWG Resistance- 26.7 ohm/ft 80.3 ohm/m. Wire Diameter- 0.16 mm.
This item is for experienced users only!
DIY atomizers may pose risk of injury if you do not know what you are doing.
Use at your own risk, please learn about rebuilding before attempting to use.
No warranty.

 

[JustinUSF]

[h=1]Kamry K101 Telescoping Mechanical Mod (body, cover & drip tip)[/h]
Beautiful and stylish anodized aluminum and chrome bottom button design. The K101 mechanical APV accepts 18350, 18500 and 18650 protected and IMR batteries.


Includes:

• One Kamry K101 telescope mod
• 1- cartomizer shield
• 1- drip tip

We also have the Full K100 kit which includes everything you need except juice!




Never use non-rechargeable batteries in this or any other e-cig device! Only use the recommended batteries for this unit, it's for your safety.

 

[JustinUSF]

[h=3]Kamry X10 Bottom Coil Clearomizer Tank (BCC), 4ml[/h]This is Kamry's version of the popular Protank and offers enhancements over Kanger's version. This one lets you use your own 510 drip tip mouthpiece and offers a more generous 4mL eLiquid capacity. The design is very similar; bottom coil with a screw off base, except it is thick poly, not glass. While it does come with it's own coil head, it is compatible with Kanger's EVOD coils (original short stem heads), but NOT Protank or T3S coil heads.



Get your X10 replacement heads here!



Compatible with any 510 threaded device.



Each tank includes:

• Metal Sleeved 4mL Poly Tank
• 2.4ohm Coil Head
• Metal Barrel Style Drip Tip

 

[JustinUSF]

Large Anodized Aluminum Ming Vase-shaped Drip Tip - Purple. Fits 510, 901, 808D-1


Replaces the cartridge on the atomizer for ease of dripping directly on the atomizer.

Drip tips aren't just for dripping! Use them on Carto's instead of pulling those caps off.


A rubber o-ring seals the tip and minimizes leaking while improving airflow.
Smooth cool feel. Larger size than the normal ming style. Length is 1.25" (31mm).


Pick up several to color code and keep track of juices in your atomizers and cartomizers!

Warranty is for defective product only.

 

[JustinUSF]

[h=1] Vision Express Mini BCC eGo Clearomizer Kit The Express Mini eGo BCC kit by Vision is a low cost e-cigarette that is rechargeable and refillable. It has a 350mAh 3.6-4.2v battery that will keep you going 3-6 hours easily. This kit includes a Bottom Coil Clearomizer for a great vaping experience. We make this kit available so you can try a quality Personal Vaporizer without spending a lot, it also makes a great gift for a smoking friend or family member! Available in stainless or black matte.[/h][h=1][/h]The bottom coil clearomizer in this kit holds 1.6ml of e-liquid to keep you going for a long time on one fill. It's nicely shaped, leak and spill resistant. It is very easy to fill, by just turning upside down, unscrewing the bottom, tilting and dripping e-liquid into the side (try not to get liquid in the center, that is for air flow). No need for syringes with this kit!


Click on the links here for extra CE4 Clearomizers, Vision Clearomizers, or the newer Changeable Coil CE4 Clearomizers. These are all compatible with this device.


This device outperforms the smaller e-cigs considerably, it will not disappoint you!

Be sure to add a bottle of your favorite e-liquid so you can refill many times!

Our Express Mini BCC eGo kit includes:
1 x 350mA mini eGo battery - 510 threaded
1 x Bottom Coil Clearomizer - 1.6ml capacity - 2.4 ohm coil
1 x USB charger
1 x Hard side case

 

[JustinUSF]

[h=1]SMOK E-Pipe, chrome[/h]This is a great looking and simple mod. This mod works every time thanks to a simple design and a mechanical switch. The e-Pipe works with a flat top 18350 battery which is easily installed by unscrewing the bottom of the device. It has a 510 connection so you can use any 510 threaded clearomizer or cartomizer. Devices requiring outside eGo threads will need a 510-eGo adapter.


The chrome finish is highly polished and looks great with a Redux Clearomizer, Chrome Mini Smoktank or Stainless EMDCC (as shown in the pictures).


The price is for one (1) Chrome e-Pipe. Redux, drip tips and other accessories sold separately.



The E-Pipe requires one flat top 18350 IMR battery, It will not work with button top IMR's.


Never use non-rechargeable batteries in this or any other e-cig device! Only use the recommended batteries for this unit, it's for your safety.

Choose the Make It a Kit option to get batteries and a charger at a discounted price.

 

[JustinUSF]

[h=1]Innokin iTaste SVD Telescoping Variable Power, VV APV, Stainless[/h][h=1] [/h]The SVD Advanced Personal Vaporizer is massive, powerful, reliable, full featured and very well built. With this device, Voltage or Wattage is variable 3-6 volts or 3-15 watts respectively, using a single 18350, 18500, 18650 IMR battery, (all available separately and discounted here when you make it a kit). It can check atomizer/carto resistance and battery voltage too! The Telescoping design allows for different length batteries.


It will work with flat or button top IMR's and protected Li-Ion batteries.


Never use non-rechargeable batteries in this or any other e-cig device! Only use the recommended batteries for this unit, it's for your safety.

Choose the Make It a Kit option to get batteries and a charger at a discounted price.


Features:

• Variable Voltage: voltage can be adjusted from 3.3 – 6.0 volts in .1 volt increments.
• Variable Wattage: Wattage can be adjusted from 3.0 – 15.0 W in .5 watts increments.
• Short Circuit Protection.
• Reverse Battery Protection Circuit
• Battery Voltage Detection
• Resistive Load Detection ( Ohms meter )
• ON/OFF battery switch
• LED Battery Power Display
• Low Voltage Warning
• Overtime Vaping Warning
• Telescopic Tube supports 18350, 18500 or 18650 batteries
• Battery safety protection
• Very compatible ( Threads fit iClear10, iClear16, iClear30, CE4, CE5, eGo, T2, T3, VIVI NOVA and 510 etc)
• Change battery and switch VV or VW have parameter memory function
• Built-in 3 Character Display ( Ohms meter , Volts /Watts , Atomizer voltage output )

The price listed is for the unit only, packaged in a box with easy to understand iTaste SVD User Manual. << click to download it now!

 

[Dieseler]

Really like the display window . Too bad its not streamlined similar to the Sigelei vv/vw telescoping device where the bottom tube is flush with the top portion when using a 18350 battery or i would purchase.
Otherwise very nice.

 

[JustinUSF]

[h=1]L-Rider Lambo 6.0 Variable Power, 20 Watt APV, Stainless[/h][h=1] [/h]The new Lambo 6.0 Advanced Personal Vaporizer is powerful, reliable, full featured and very well built. With this device, Voltage or Wattage is variable 3-6 volts or 0-20 watts respectively, using a single 18650 IMR battery, (available separately and discounted here when you make it a kit). It can check atomizer/carto resistance and battery voltage too!


It will work with flat or button top IMR's and protected Li-Ion batteries.


Never use non-rechargeable batteries in this or any other e-cig device! Only use the recommended batteries for this unit, it's for your safety.

Choose the Make It a Kit option to get batteries and a charger at a discounted price.


Features:

• Variable Voltage: voltage can be adjusted from 3.3 – 6.0 volts in .1 volt increments.
• Variable Wattage: Wattage can be adjusted from 0.0 – 20.0 W in 1 watts increments.
• Short Circuit Protection.
• Reverse Battery Protection Circuit
• Battery Voltage Detection
• Resistive Load Detection ( Ohms meter )
• LED Battery Power Display
• Low Voltage Warning
• Battery safety protection
• Very compatible ( Threads fit iClear10, iClear16, iClear30, CE4, CE5, eGo, T2, T3, VIVI NOVA and 510 etc)
• Built-in LED Display ( Ohms meter , Volts /Watts , Atomizer voltage output )

The price listed is for the unit only, packaged in a box with easy to understand user manual.