New to ecf

[St0rm]

Hey I'm Storm and I'm new to ecf, have been lurking and learning though.

I started out with the joyetech e-roll and used it quite a bit. I think it was after three months that I felt the need for more. I googled and watched some youtube and bought the emow from kanger.

Probably due to user error I killed the battery, I also didn't like the 510-battery loader which felt kinda cheap and didn't connect well from the start. So instead of sending it back I bought the mvp..

Some mods and months later I now rock the Lemo on the sigelei 100w!

Vapetastic new year!!

 

[bacc.vap]

Hello and welcome.

 

[Warpigs]

Welcome to ECF!

 

[St0rm]

Thank you!

 

[2naphish]

welcome to the ECF. wishing you a smoke free New Year.

 

[Steven G]

Greetings Storm and Welcome to the ECF................................Enjoy................................

 

[wshanncap]

Welcome to the forum. The Lemo is my go-to tank as well.

 

[Warpigs]

Welcome to ECF!

 

[Mccannch]

Glad you are finding success in vaping. That was about like my progression, now I own so many attys I forget sometimes what all I own. There is a great Lemo thread in the rebuildable section. Lots of information, stop by when you get your 5 posts and say hello.

 

[Chilly Bone]

I'm new here as well... Looking forward to getting out of 5 post jail!

 

[St0rm]

Thank you all! I really enjoy the Lemo! Got a 1 ohm 4 strands twisted 28 kanthal at a 1cm screwdriver, about 5 wraps, at 40 watts its insane and it can go a lot higher haha. What crazy builds have been achieved on your Lemo Mccannch?

Welcom to you too Chilly!

 

[Mccannch]

Thank you all! I really enjoy the Lemo! Got a 1 ohm 4 strands twisted 28 kanthal at a 1cm screwdriver, about 5 wraps, at 40 watts its insane and it can go a lot higher haha. What crazy builds have been achieved on your Lemo Mccannch?

Welcom to you too Chilly!

I have done quite a few different builds. I always keep one of them setup with a standard coils 26 ga wrapped around a 3mm bit around .8 ohms. It's a very consistent vape and I know I can always fall back on it. Currently I'm trying to rekindle my interest in temp control with DNA 40. I have a vapor shark that is acting crazy on me, from the first shipment. Yesterday I got a Bap40 in the mail and it's solid so far. I hope to get some good temp control builds in now!!

 

[St0rm]

Temp control would make life SO much easier! What atty do you use? Im still holding off on the temp control, I first want to build an Okr box, seems like a do-able challenge. But I do believe that the dna40 is the next big step in the vaping world, after all the high wattage boxes that's come out.

 

[St0rm]

Just saw some pics of the bap40, looks very sturdy, very nice! Its made of some sort of plastic right? It must be very light! Looks pretty pocket friendly, have fun with those builds!

 

[Mccannch]

The bap 40 is 3D printed. You can actually buy the case off of a website shapeways.com. I ordered some parts to try and build my own box someday. This thing is much smaller than I thought it would be, it's very comparable to the vaporshark in size, and half the weight with both batteries installed. They only had white in stock when I ordered it and I know it will get dirty but oh well. All my temp builds have been in the Lemo for now. You need a lot of coil to make the resistance and the Lemo deck allows for the room.

 

[St0rm]

It sounds like a great design! All the scratches and dirty patina just makes it more unique!