Nzonic V3 help please.

[icecreamsanta]

Hello, I need some help. My new gorgeous Aspire Atlantis tank just came in the mail and I've been dying to try it out. But there's one problem, none of my vapes with fire it. I tried it on several..

Evic - "Atomizer short"
iTaste MVP 2 - No reply, but feels stuffed like there's no chance of it ever firing hah.

Nzonic v3 mech mod - I need some help with this. unlike my other vapes, this one when i try inhaling it actually feels like it will let me, except I can't turn the mech mod on.. I have a 24A Highdrain battery fully charged, extended body piece of the nzonic (it's a telescopic thingy) and I purchased a "safety fuse" that i have no clue how to use it or where it goes, so i just sat it on one of the ends of the battery and screwed the top on, (It was magnetized to the battery) but when I get everything set and ready to go, and press in the little ring and the bottom of the nzonic, nothing happens. There's no on switch, button, lever, glowing dot. snozzle frazzle(not a real thing) I just desperately want to try out this bad boy.. any help?

 

[icecreamsanta]

... hello? anyone.

 

[QU1T]

I am a noob, I can tell you though strait off, the MVP will not fire a .5 ohm, which is what the Atlantis is if I am not mistaken...
Your mech mods should though, perhaps your fuse is faulty, I bought a few and one was DOA,
You can test to see your Atlantis works OK with the MVP's ohm reader and then just fire to test with out the fuse...

Some more experienced Guru should be along shortly though!

 

[icecreamsanta]

I am a noob, I can tell you though strait off, the MVP will not fire a .5 ohm, which is what the Atlantis is if I am not mistaken...
Your mech mods should though, perhaps your fuse is faulty, I bought a few and one was DOA,
You can test to see your Atlantis works OK with the MVP's ohm reader and then just fire to test with out the fuse...

Some more experienced Guru should be along shortly though!

Thank you, I would like to try out that ohm reader, except the atlantis tank is filled and i really don't wanna empty a full tank :/

 

[athousandyears]

Pretty sure you can check the ohms of the atlantis without emptying it. Just attach it to the MVP and push the P and U buttons at the same time. This will give you the resistance of the coil which should be 0.5. Also, to which end of the battery did you attach the fuse? It probably goes on the negative end.

 

[icecreamsanta]

Pretty sure you can check the ohms of the atlantis without emptying it. Just attach it to the MVP and push the P and U buttons at the same time. This will give you the resistance of the coil which should be 0.5. Also, to which end of the battery did you attach the fuse? It probably goes on the negative end.

Ahhh thank you, I put the Atlantis onto the MVP and did what you said, I got a "0.5" pop up on the screen, and then I guess got a recommendation of power because shortly after I got a "4.1" which was volts i'm guessing. But it doesn't work. Tried it on my evic at 4.1, doesn't work. Hooked it on my mech mod with the safety fuse on the negative side, nothing. Someone told me that I might need a 18500 battery or something other than a 18650

 

[Stosh]

Depends on the rating of the fuse you purchased, with a fully charged battery 4.2 volts and a 0.5Ω coil you are drawing 8.4 amps. This may be higher amperage than the fuse is rated to handle, which will make it trip instantly.

Using a mech you need to figure what voltages, ohms and current (amps) you plan on using to operate properly. A multimeter is also very highly recommended, it's useful in many way in servicing your mech mod.

This link will give you an easy way to figure the numbers....http://www.the12volt.com/ohm/ohmslawcalculators.asp

 

[athousandyears]

The reading you got after the 0.5 is the current available voltage of the battery, not a recommendation of volts to apply to the coil.

 

[QU1T]

Ahhh thank you, I put the Atlantis onto the MVP and did what you said, I got a "0.5" pop up on the screen, and then I guess got a recommendation of power because shortly after I got a "4.1" which was volts i'm guessing. But it doesn't work. Tried it on my evic at 4.1, doesn't work. Hooked it on my mech mod with the safety fuse on the negative side, nothing. Someone told me that I might need a 18500 battery or something other than a 18650

The 4.1 reading is the power left in your MVP's battery

Edit, Ninja'd.

 

[classwife]

Moved to APV Discussion from Simple Solutions


Simple Solutions is to assist the Beginning Vaper with getting started

 

[Miata GT]

Bottom line is the MVP won't fire that low of a resistance. As for your Nzonic I can't say but I just bought an Atlantis tonight and the 510 connections is much shorter than most of my other attys. So short that it would not connect to some that didn't have an adjustable pin.

 

[rodeo302]

Try pulling the fuse out and shortening your mech mod to fit the battery without it then put the Atlantis on and see if it works.

 

[Jjshbetz11]

Why don't u just vape it without the fuse?

 

[93gc40]

Also check the atomizer for a short with a meter, NOT A VAPE. Try a different coil in you atomizer. Try adjusting your mechs firing pin or switch.