personal opinions what looks best with kfl+

Status
Not open for further replies.

koriandjon

Senior Member
ECF Veteran
Verified Member
Apr 19, 2014
264
260
spokane, wa
Wanting opinions of everyone who's been around on what they think looks best with the kfl+. I have an evic now but hate how it looks. I know I want something stainless steel and I can only afford clones or something under 100 bucks would prefer to spend closer or under 50 bucks though if possible. I don't sub ohm mostly anywhere between 1.5-2.5 ohms and I use 650 batteries currently. I've tried looking around myself but there is so much out there and it's hard to imagine what they would look like with the kfl+. Any and all opinions are welcome please staring at the evic combo is getting to me...I know it shouldn't matter but it does...and you all are the pros. Oh and another thing I don't know if mods do this but the evic times out at 10 secs and it drives me batty will a mod do that too?
 

db13berry

Ultra Member
ECF Veteran
Verified Member
Mar 24, 2011
2,149
1,594
USA
3enequ3a.jpg


SVD with KFL.

Sent from my couch using Tapatalk.
 

koriandjon

Senior Member
ECF Veteran
Verified Member
Apr 19, 2014
264
260
spokane, wa
Did i see someone say orange tank options for the kfl+? Ooo might have to look into that I love orange. And never been much of an svd fan but appreciate the opinion I do like the look though much better than the evic and kfl+ but the nemesis is damn sexy. In the 3 some picture what is the 1st setup? That one looks really really good together.
 

tearose50

Vaping Master
ECF Veteran
Verified Member
Feb 2, 2011
6,608
14,260
Tennessee :-)
KFL looks pretty sweet on a Provari, too -- if you get a beauty ring for it.

Also, there's a flat top connector available for the Evic that helps a lot on it's looks as well. My Freedom Smokes has them in stock in black and chrome. Nano kit helps the look, too, IMHO.

If you want a bottom firing switch/button and no regulation opt for a mech mod.....whichever takes your fancy. About any 22 mm tube will look good with a KFL.

You don't have to worry over 10 second cut off on any mechanical mod as they have no mechanics. Those circuits are added on regulated mods as a safety precaution, BTW.
 
Last edited:

tearose50

Vaping Master
ECF Veteran
Verified Member
Feb 2, 2011
6,608
14,260
Tennessee :-)
It's really a matter of personal preference. Using the newer styled hybrid or IMR batteries has made vaping without regulation not as risky as it would be with some older batteries.

This says it best: http://www.e-cigarette-forum.com/forum/rebuildable-atomizer-systems/562106-ecf-sub-ohm-advisory.html, which I quote below.

"1. Batteries

Modern batteries are extremely safe compared to those we used to have. If a genuine IMR or hybrid rechargeable cell is destroyed by sub-ohming or some kind of fault, then what appears to happen is that it melts down without any significant out-gassing. The gas generation is the danger factor as it can lead to an explosion, if it takes place in a sealed device. A hot APV does not appear to be a significant danger except in some sort of fire-risk situation (maybe in a gas station, or on an old foam couch/sofa).

What is certainly an issue, though, is if a counterfeit battery is used by mistake; or if someone deliberately uses an ICR (regular Li-ion) cell instead of the modern type of safer-chemistry cell. In that case there could be a significant outgas risk in the event of a battery failure, which translates to risk for an explosive event.

Please make sure to use genuine IMR or hybrid cells from a reputable source, and DO NOT USE regular Li-ion cells (ICR) for heavy-duty applications like this."

Though I do use some unregulated systems, I prefer the more consistent vape I get from my regulated mods and changing the voltage or wattage when I want with the push of a button or twist/turn of a dial. 10 seconds is plenty of time for me. :)
 
Last edited:
Status
Not open for further replies.

Users who are viewing this thread