Picture of Your Setup Part 2!
- Thread starter QuietProSF
- Start date
- th_trl_thread_readers 0
- Status
It's great until you need to charge it. The usb is on the bottom
It's great until you need to charge it. The usb is on the bottom
most are. There are some now where you plug in the usb on the side of the battery, but the rubber cover can go missing
It's a Starbucks coffee mug and a mmv nanos sleek in 350 mode
Pretty sweet little mod. Check out mmv's website
Sent from my iPad using Tapatalk
RIP Pinky... I loved my girlie mod... You will be missed...
what happened to it?!
Sigelei Zmax V5 telescopic just after I installed a heavy duty aftermarket tactile switch. The switch is rated for 1,000,000 clicks which should be good for a little more than four years at my vaping rate.
Fresh from my local b&m my all copper manhattan replacing the king and still rocking the provari as my driving vape kinda getting disappointed with the aspire Nautilus thinking about making the switch to a better setup for it to make it more fun 
replacing the king and still rocking the provari as my driving vape kinda getting disappointed with the aspire Nautilus thinking about making the switch to a better setup for it to make it more fun
Updated Collection End of Summer 2014
Just GG Brass-Tobh V2.5 RDA-Tobh DT, King SS-Vulcan RDA-MLV DT, Brass Hades-Cerberus RDA Hybrid-MLV DT,
Brass Cartel-Tobh V2 RDA/Brass Sleeve/Top Cap-Tobh DT, Copper Cartel LE-Stillare V2 RDA-Tobh DT,
Chi Megan 318-Nucleus RDA-RSM DT,
Brass Chi You/Engraved Tubes/Flat Cap-APO RDA-MLV DT, Naval Brass Chi Sleek-Cyclone RDA-RSM DT,
Poldiac Nanos LE Brass-Kayfun Lite V2+/Orion Flat Cap/Frosted Clear M-Tank-MMW DT
Just GG Brass-Tobh V2.5 RDA-Tobh DT, King SS-Vulcan RDA-MLV DT, Brass Hades-Cerberus RDA Hybrid-MLV DT,
Brass Cartel-Tobh V2 RDA/Brass Sleeve/Top Cap-Tobh DT, Copper Cartel LE-Stillare V2 RDA-Tobh DT,
Chi Megan 318-Nucleus RDA-RSM DT,
Brass Chi You/Engraved Tubes/Flat Cap-APO RDA-MLV DT, Naval Brass Chi Sleek-Cyclone RDA-RSM DT,
Poldiac Nanos LE Brass-Kayfun Lite V2+/Orion Flat Cap/Frosted Clear M-Tank-MMW DT
Playing around with different combinations.
East meets West . . . authentic Chi You with 454 Big Block
East meets West . . . authentic Chi You with 454 Big Block
Sigelei Zmax V5 telescopic just after I installed a heavy duty aftermarket tactile switch. The switch is rated for 1,000,000 clicks which should be good for a little more than four years at my vaping rate.
That is awesome!
I wish I could install one of those on one (or both) of my iTaste SVD's, as the button has already failed on one of them, and I think the second one is starting to fail as well
Of course I'm not sure it would even be possible with the SVD.
Ember mod, still needs buff & polish but almost done. ALso looks like the goat photobombed my pic.
[/URL][/IMG]
Beautiful mod! Of course, all of yours are IMO but I love patina too.
Have you ever thought about/tried to force patina your attys?
I'm leary of putting the chemicals in patinas & clear coats directly in contact with juice & heat. If I find a way to know it's safe & durable I'd try it but not til then.
. Well today my ocd cried enough, and out came the dremel, and I think all in all it came out pretty good.Edit: the top tube had deep scratches all the way around, quite a few of them in fact.
Pulled the topper off the Tugboat and pulled the pin out... Pushed it back in and hit it lightly with a hammer now it only reads Shorted won't read or fire. Tried it on my Kayfuns and drippers just says shorted... Bummer...
Picked up this little guy today to use for my Kentucky Edition Tugboat! #26 of the 30 that were made
Hey everyone, just wanted to share my latest find...
So I was browsing "slowtech" when I came across the Smok RDA Dripper...Ive been looking for something smaller for my IPV2 so I figured what the heck,its 7 bucks...BEST 7 bucks spent of my vaping career to date! I did have the air hole drilled out to about 1.9mm because the draw was a little tight for my liking- (direct lung inhales) This little guy is AMAZING for flavor and blows huge clouds with a 50/50 mix juice! Its honestly like or what I would imagine it would be like if you used the chimney section out of a KayFun or Russian91% as a dripper! It does get warm with low Ohm builds as the drip tip is connected to the unit and the coil wraps close to the cap wall. I keep it around 1.0 to 1.3 ohm builds at around 20 watts and I love it! So if you got 7 bucks, love flavor chasing and dont mind waiting a month or more I would definitely recommend!!
So I was browsing "slowtech" when I came across the Smok RDA Dripper...Ive been looking for something smaller for my IPV2 so I figured what the heck,its 7 bucks...BEST 7 bucks spent of my vaping career to date! I did have the air hole drilled out to about 1.9mm because the draw was a little tight for my liking- (direct lung inhales) This little guy is AMAZING for flavor and blows huge clouds with a 50/50 mix juice! Its honestly like or what I would imagine it would be like if you used the chimney section out of a KayFun or Russian91% as a dripper! It does get warm with low Ohm builds as the drip tip is connected to the unit and the coil wraps close to the cap wall. I keep it around 1.0 to 1.3 ohm builds at around 20 watts and I love it! So if you got 7 bucks, love flavor chasing and dont mind waiting a month or more I would definitely recommend!!
[/ [URL=http://s1291.photobucket.com/user/Badinfluence357/media/20140828_192226_zps7vfdkfqm.jpg.html]- Status
Similar threads
