Picture of Your Setup Part 2!

[Quantum Mech]

 

[The.Drifter]

Current rotation pic of my vape table

 

[The.Drifter]

Felt like some Cloudz today, so I broke out the sigelei and built some Claptons this morning

32G over 26G claptons, 4 wraps over 3mm pin 0.33 ohms.

Can drip directly thru the air holes with this sleeve

 

[PapaGeno21]

Try holding the 32 tighter as you spin the 26 they will wrap tighter. I loveeeeeeee claptons.

 

[Northy]

Wow guys, I'm in a totally different place... all mech.

A couple of these have moved now, a couple of new additions on board too.

 

[cindycated]

That was always one on my list to get and some reason never happened. I bet it has good flavor, is it the one with all the mounting points or just two. I know that one clone that was out only was a dual coil.

It's a sexy little dripper and works great for me, but air is abysmal by today's standards (this atty is extremely old-school) - great MTL, awesome flavor, but if you lung hit at all, you probably wouldn't like it much. The deck is set up for 4 dragons, but I've had no trouble building it with duals and even a single (a little wimpy with a single though).

Air comes in from holes at the top, fills an outer chamber, then works its way into the inner chamber. It's mostly just my little porn star now. I don't use it much.

 

[cindycated]

Only a tank a day. I don't vape like it's going out of style. Fill-up right before bed everynight.

Plus it's easy-fill. Chamber sticks to the cap so filling is just like a protank/subtank. The orchid on the otherhand had to be modded for the cap to fit, so i have to fill it via the screw.

With the Orchid and KFL, I make sure the top o-ring is nice and tight, attach chimney to the tank and screw that assembly onto the base. That way, the chimney/chamber assembly stays loose and I can just screw the base off to fill. I hate that little fill screw at the bottom.

 

[rhelton]

It's a sexy little dripper and works great for me, but air is abysmal by today's standards (this atty is extremely old-school) - great MTL, awesome flavor, but if you lung hit at all, you probably wouldn't like it much. The deck is set up for 4 dragons, but I've had no trouble building it with duals and even a single (a little wimpy with a single though).

Air comes in from holes at the top, fills an outer chamber, then works its way into the inner chamber. It's mostly just my little porn star now. I don't use it much.

I wish someone would give me that title

 

[QU1T]

Wow guys, I'm in a totally different place... all mech.

A couple of these have moved now, a couple of new additions on board too.

What are the non GP mechs there mate? care to list please? (toppers also plz!)

cheers

 

[Northy]

From left to right

Atties: Raptor, Rose V2, Quasar, Hellfire top hole 22, Hellfire top hole 20, Sat22, Hellfire side hole 22, Hellfire V1 style, Hellfire short crank, Hellfire V1.

Mods: Oros, GP Paps, Super-T Workhorse, GP Paps Luxe, MCR 101 SL (old style), GP Paps, MCR 101, MCR101 SL, MCR 101 Hiduron, MCR 101 SL Hiduron LTD edition.

I know there's a lot of MCR & GP gear there. I've tried a lot of mods and these two are the ones that stand out for me as being top notch. If I could get another Super-T mod I would also, so reliable.

 

[QU1T]

Nice one mate!, idd loving those MCR's! and those Hidurons look like the dogs nuts. - the rest look totally crisp also, very nice!

 

[Northy]

Out of those atties my favs are the RoseV2, Quasar, Sat22 and Hellfire short crank.

If I never had anything else I could survive just fine... the quality of them would probably last a lifetime too.

 

[a_e_u]

I'm a late adopter....my one & only gear purchase in 2015, the Squape R(s).

 

[Northy]

I'm a late adopter....my one & only gear purchase in 2015, the Squape R(s).

Nice one a_e_u. I've been eying up a Squape r for a while now. You happy with it?

 

[a_e_u]

Nice one a_e_u. I've been eying up a Squape r for a while now. You happy with it?

Thanks Northy,

Unfortunately mine requires some pampering & lots of cleaning. I experienced the dreaded jumping ohms & even random "check atomiser" msgs on my dna 30 on my 1st few setups. But strangely enough, after applying wd40 to the 510 pin, the ohms reading stabilised at its correct value. Other than that, I'm pretty satisfied with the mtl vape on the w deck.

 

[HighPlainsPuffer]

I took a couple family pictures yesterday while I was "cleaning"

 

[PapaGeno21]

Today's vape. Sig 150TC and velocity clone. 2mm inside diameter claptons. I'm calling them baby claptons lol I just made them. 28g core, 32g wrap. 9 wraps coming in at .71 ohms total. 45 watts it's working great!

 

[Flip Vaper 77]

Sent from my iPad using Tapatalk

 

[Tonkpils]

Sent from my iPad using Tapatalk

lightly strum (like a guitar) that right coil to get rid of that hot spot!

 

[stillnotsmoking]

Bourbon & vape

Sent from my SM-G900V using Tapatalk