Picture of Your Setup Part 2!
- Thread starter QuietProSF
- Start date
- th_trl_thread_readers 0
- Status
What tanks are those? I like short tanks like the Goblin Mini and my Kabuki's. Those look perfect to me 
Seems to be Tobeco Super Tank Minis. Same as the tank I have on my Snow Wolf above.What tanks are those? I like short tanks like the Goblin Mini and my Kabuki's. Those look perfect to me
What coils are you using in the Super Tanks? I am having trouble finding Tobeco coils locally and picked up a pack of Tritons to try out.Current rotation for today
Thx!
I got a few packs each of the Tobeco SuperTank .2 and the .5 ohm coils from here : Tobeco Supertank Coils - Supertank, Matrix - Tobeco, High Voltage - Tanks & Coils
Last edited:
What tanks are those? I like short tanks like the Goblin Mini and my Kabuki's. Those look perfect to me
Been having my goblin in a box for almost 2 months now... Was going to swap with the magister i have on now but it seems that i cant put my magister down lol
Maybe next month i'll open it up and tinker with it.....
Sent from my iPhone using Tapatalk
Yeah, my GM is boxed also. Between wicking/leaking issues and mod damage I didn't think it was really worth the hype. I could deal with the slight leaking now and then, but didn't take kindly to the scratches on the top of my new IPV D2 despite the care I took when attaching it
Yeah, my GM is boxed also. Between wicking/leaking issues and mod damage I didn't think it was really worth the hype. I could deal with the slight leaking now and then, but didn't take kindly to the scratches on the top of my new IPV D2 despite the care I took when attaching it
Oh yes the scratching rumor... Because of the way the gm's base was made so the material was really hard/sharp... After a few twists and ur mod is scratched... The wicking/leaking part i am yet to endure as i am still drawn to my majister lol.... But many has complained about the leakages... But meh, i had been using zephs before so leaking is part of the "taming" period [emoji16]
Sent from my iPhone using Tapatalk
I never really have had a leaking issue. But I have noticed I have to slightly over wick or I could see leaking issues. But I agree with the damage it causes to the top of mods. I never have used it on my Sigelei 150tc because I'm too worried it will tear that "rubber" cover and I can't use it on the RX200 because it will set too low inside "tank trough". I only use it on my Koopor Mini. But I love my AromamizerYeah, my GM is boxed also. Between wicking/leaking issues and mod damage I didn't think it was really worth the hype. I could deal with the slight leaking now and then, but didn't take kindly to the scratches on the top of my new IPV D@ despite the care I took when attaching it
I saw a vendor offering very thin washers in 22mm and 23mm to protect the tops of your mods. They were very thin, .5mm or less. I figured I'd order some in case I want to give it another shot (too bad the damage is done though). I think it was either 101vape or KP...
Good thing i am on a mech hihi... Not so much of scratches... Dont have any platings or coatings.. Just plain ole metals.... So far whatever i slap on my v3 and smpl... K100 and one more mech which i tried looking for its name and make... No scratches whatsoever YET...
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
I used a washer that I had laying around my shop and it worked but it was too think and made the set up look janky. A thinner one would be better
Found em, they're at KP and are called the KP Mod Guard
KP Mod Guard - 5 Pack
at .5mm thick they only seem to be about the thickness of heavy construction paper and you can get them in 22mm and 23mm diameters...
Just finished building new coils for this badboy setup (I splurged, both authentic) freshly wicked and dripped, just set my buddies smoke detectors off haha
Sent from my iPhone using Tapatalk
Hmm...I got a little something to match clouds with that Rig...A little something called Magic Blue checking into this thead once again...
- Status
Similar threads
