Picture of Your Setup Part 2!
- Thread starter QuietProSF
- Start date
- th_trl_thread_readers 0
- Status
Well, I do have another married pair, but I'm trying to keep them in my X Cube II. But if they happen to be fully charged, I would throw them in.difference is, I don't put it down when the battery dies...I just swap it and keep on goin
Sent from the future with my Flux Capacitor enabled Note 5
a few - List of songs written by Willie Dixon - Wikipedia, the free encyclopediaOle Willie, he wrote a couple of songs in his day
Look at the list of "Subsequently recorded by" - probably the most influential writer to Rock music
I'd like to compare it Robert Johnson's list but they don't include that at his discography page
Robert Johnson discography - Wikipedia, the free encyclopedia
Edit - Dust My Broom - Wikipedia, the free encyclopedia
Here are some Provaris and a bonfire in my living room a couple of years ago for some on topic content
Last edited:
My Moto Plus has finally arrived. I'm definitely enjoying the vape I get from this and so I now have another travelling buddy
a few - List of songs written by Willie Dixon - Wikipedia, the free encyclopedia
Look at the list of "Subsequently recorded by" - probably the most influential writer to Rock music
I'd like to compare it Robert Johnson's list but they don't include that at his discography page
Robert Johnson discography - Wikipedia, the free encyclopedia
Edit - Dust My Broom - Wikipedia, the free encyclopedia
Here are some Provaris and a bonfire in my living room a couple of years ago for some on topic content
Dixon is probably the most influential writer in modern music history.
Robert Johnson was an amazing bluesman, wasn't much for creative song titles though
I like your bonfire, they do provide a nice DC signal.
Yes it is a unfinished Cuboid and a unfinished Triton 2, Was bored, and I need to finish it, had only part of the chimney done on the atty. The Atty was done in Catia, and the Cuboid was done in Unigraphics NX9. I never played with the studio photo software in either program, so I am going to finish them and see if I can do something better?
I like seeing the different setups people have in this thread!
I knew it wasn't solidworks you drew the mod in! Wrong coordinate icon. Is the mod a complete assembly or just the shell? Haven't tried to draw an ICB yet! My attention span is too short for all those components! lol!Yes it is a unfinished Cuboid and a unfinished Triton 2, Was bored, and I need to finish it, had only part of the chimney done on the atty. The Atty was done in Catia, and the Cuboid was done in Unigraphics NX9. I never played with the studio photo software in either program, so I am going to finish them and see if I can do something better?
I like seeing the different setups people have in this thread!
LOL, The Mod was in NX9, and no so far only the shell is done, well I do almost have the battery door assembly done!
But that is when I got bored with NX and went to do the Triton 2 atty in Catia, I was finishing the coil and starting the chimney. But I got tired and quit, need to get back at it! Never used Solidworks, but I heard it is a lot easier to use than Catia! I've seen it and recognised some of the icons between the 2! Maybe someday I'll get a chance to use it?
I am NOT going to do a ICB, no thanks!! Back when I was learning robotics I knew enough about electronics to be dangerous! Ohms law and kirchhoff's law??
That is what made me get away from robotics! 
But I did see in both software's I do have PCB workbenches? HHHMMMM.... Maybe I can just fake it in?
Never used anything but Solidworks & I'm self taught with a little help from the guys here at work & because I've done some drawing in Mastercam it came pretty easy!LOL, The Mod was in NX9, and no so far only the shell is done, well I do almost have the battery door assembly done!
Never used Solidworks, but I heard it is a lot easier to use than Catia! I've seen it and recognised some of the icons between the 2! Maybe someday I'll get a chance to use it?
I am NOT going to do a ICB, no thanks!! Back when I was learning robotics I knew enough about electronics to be dangerous! Ohms law and kirchhoff's law??
But I did see in both software's I do have PCB workbenches? HHHMMMM.... Maybe I can just fake it in?
It's the V1 I have had a hard time in geting it Glasgow is not the best city for vape store.s
I have one, but it's a clone by Tobecco. I had to hunt for this nonetheless. I'm very pleased with it [emoji1]
Sent from my SM-G900I using Tapatalk
Going to do a TI build on it and do the temperature thing on it to.I am a bit Scared as I have read a lot but as long as you do as I have read it is OK I hope
Be safe.
I haven't really tried TC as of yet. I'm a wuss I suppose.
Sent from my SM-G900I using Tapatalk
I haven't really tried TC as of yet. I'm a wuss I suppose.
Sent from my SM-G900I using Tapatalk
- Status
Similar threads
