Picture of Your Setup Part 2!

[Muggs]

How's she vape Muggs?

Also how is the DIY going, still barrel steeping anything?

She is vaping well my friend. Money very well spent. The 1st batch is gone I was actually thinking of starting another one. Maybe a new recipe not sure.

 

[f1vefour]

She is vaping well my friend. Money very well spent. The 1st batch is gone I was actually thinking of starting another one. Maybe a new recipe not sure.

Good to hear, I'm looking at getting this clone or something SX350 based.

Best of luck on your new batch, the previous was a really nice vape.

 

[GreatestUnKnown]

Hi, did you get the dual 24g through the stock centre hole ok ?

Oh, and how many wraps did each have.

Thanks

I would like to know as well, I can't even do a dual coil with triple twisted 32g on my Atomic.

When I pulled the center pin for modding to BF I went ahead and drilled out the wire capture point as well. I think i will need to drill out the negative capture points soon so i can run some parallel setups next.

6/7 wraps on 1/16th ID for 0.28Ω

I also used the dremel grind attachment to counter sink the air hole openings to eliminate any chance for "whistling"

 

[evgeny131]

Since the high end mods thread is closed......
A little 3M Hand Glaze, a Cartel Copper Limited Edition, Stillare RDA and Five Pawns Mixology Lucena = A beautiful weekend....

 

[chadsmo]

Since the high end mods thread is closed......
A little 3M Hand Glaze, a Cartel Copper Limited Edition, Stillare RDA and Five Pawns Mixology Lucena = A beautiful weekend....

http://www.e-cigarette-forum.com/forum/showthread.php?t=565483

 

[Anticlus]

Pretty new to vaping

 

[MamaJaay]

Left to right

iTaste VTR with the EFest 35 amp 18650 battery, iClear 30S tank, and vaporskinz black carbon fiber wrap

Gold nemesis clone in 18350 mode with gold patriot clone dual coil. Total ohms .84

Black Madvapes EHPro Valkyrie clone (18650) dual coil. Total ohms 1.3

Love them all.


Sent from my iPhone using Tapatalk

 

[AndriaD]

Oh you don't have to sub ohm to drip just ask all the 18350 drippers out there. Build a nice 1ohm coil close the airflow a bit and it shouldn't be as bad.

I dunno, I've got a 2.2 ohm coil in my Caterpillar right now, and it can really grab me by the throat, depending on the juice. French Vanilla worked fine, but the Belgian Cocoa I tried last night really grabbed my throat and only let go when I used my inhaler, even after I lowered the watts to 6.5w. Seems I can only drip ejuice that has ZERO! throat hit of its own.

Any coil less than about 1.8 is going to be absolutely too hot for me in a dripper; I can just about handle 1.5 ohms in my kayfun, but no lower.

Andria

 

[badinfluence357]

Needs no introduction. ...lol


Sent from my LGMS323 using Xparent Green Tapatalk 2

 

[VaporDragon]

Gold Zenkote ProVari mini 2.5 with blue led, extension, beauty ring and kfl+ v2

 

[Rathamar]

Memorial Day Vaping - Disc Golf at BRP in MN - Signature Hole #4

 

[G-weezy]

How I'm rolling today.

 

[ions]

 

[vaptamist]

Super-T Simplicity 18350 + Strata with Modish Metalworks Valentino drip tip:

 

[Joka]

How I'm rolling today.

Love my stingray over anything. It's really a beautiful mod.

*tH@--j0]{A*

 

[The.Drifter]

How I'm rolling today.

One beautiful setup there Bro! I'm jelly

 

[AndriaD]

Super-T Simplicity 18350 + Strata with Modish Metalworks Valentino drip tip:

Just gorgeous! My stainless-loving heart is all pit-a-pat!

Andria

 

[chadsmo]

Memorial Day Vaping - Disc Golf at BRP in MN - Signature Hole #4

Dude, super jealous I want to play that course so bad.

 

[bigmaaark]

Just got a new toy!!! Been wanting it for a while now. Hana v3 full size! Rockin the steam turbine with a .4 build at 30 watts! Flavor heaven


Sent from my iPhone using Tapatalk

 

[txskimo]