do you even sku? 1546312
the o-ring is a bit small had to change it but after that it sits snug as a beagle...
Picture of Your Setup Part 2!
- Thread starter QuietProSF
- Start date
- th_trl_thread_readers 0
- Status
do you even sku? 1546312
the o-ring is a bit small had to change it but after that it sits snug as a beagle...
I'm using the rba Kit. So far so good, no major leaks except sometimes due to the condensation from the chamber it just leaks a bit from the bottom. A blow from the tip solve it.
Sent from my iPhone using Tapatalk powered by Evolv DNA60
Here's the set-up I'm currently vaping on, as well as the coil/juice I'm using, and the movie I'm watching 
It's my Celtic Knot ProVari P3 in 18490 mode, with a Protank 2 on top, which has the pictured (rebuilt) coil inside of it. There's also a brand new bottle of my ADV (Halo's Turkish Tobacco), and the BluRay I'm watching (Prometheus). There's nothing better than a good vape while watching a good movie
Yes I know, it's a thrilling way to spend Friday night
It's my Celtic Knot ProVari P3 in 18490 mode, with a Protank 2 on top, which has the pictured (rebuilt) coil inside of it. There's also a brand new bottle of my ADV (Halo's Turkish Tobacco), and the BluRay I'm watching (Prometheus). There's nothing better than a good vape while watching a good movie
Yes I know, it's a thrilling way to spend Friday night
Just got this box mod today, pretty nice. Got a tohb atty on her atm but looking for something bigger, maybe a dark horse. Any thoughts?
From left to right: sigelei 100w+ with a lemo sitting at 0.4 ohms with 26awg kanthal, carbon fiber fuhattan with a wotofo troll dual coil triple strand twisted 26awg sitting at 0.18 ohms and my newest edition (just picked up last night) ipv mini 30w with a subtank mini...
Attachments
Hi guys this is my everyday vape.Not the best but it workes for me:
Templar clone+plumeveil rda clone polished(i not really like the logo).
All the brass contacts on the mod are mirror polished(i think it hits harder mirror polishing the contacts).
Templar clone+plumeveil rda clone polished(i not really like the logo).
All the brass contacts on the mod are mirror polished(i think it hits harder mirror polishing the contacts).
How does the Subtank perform on the IPV Mini? I ordered a Subtank Nano to go with my iStick and/or IPV Mini.
I'm running the subtank mini on my iPV, and love it. First time I've ever been able to go over 20 watts without dry burnt hits. I li,ee it so much that it is the only tank I'm taking on vacation.
This is my Homemade Box Mod
I used rubber washers to separate the battery spring from the power so electricity (Load) does not go thru the spring--but still has
spring action for insertion of battery--wanted matching clearomizer so I painted it.
2. second pic is underside of mod cover with magnets--these attach themselves to screws heads near fire button
3. third pic is interior without battery--to show green (ground)-wire 12 guage-comming from bottom of battery to base of
510 connector. Red wire (positive)+ comes from top of battery to switch and then to center pin of 510 connector. I painted bed of
battery cradle red for effect. Used old battery clip from worn out doubleAA-battery charger soldiered to copper strip for positive end of
battery connector.
4. fourth pic is interior with battery installed.
5. final pic is original sloppy wiring but it did fire-but I was not satisfied with design.
I used rubber washers to separate the battery spring from the power so electricity (Load) does not go thru the spring--but still has
spring action for insertion of battery--wanted matching clearomizer so I painted it.
2. second pic is underside of mod cover with magnets--these attach themselves to screws heads near fire button
3. third pic is interior without battery--to show green (ground)-wire 12 guage-comming from bottom of battery to base of
510 connector. Red wire (positive)+ comes from top of battery to switch and then to center pin of 510 connector. I painted bed of
battery cradle red for effect. Used old battery clip from worn out doubleAA-battery charger soldiered to copper strip for positive end of
battery connector.
4. fourth pic is interior with battery installed.
5. final pic is original sloppy wiring but it did fire-but I was not satisfied with design.
The dark horse has a lot of airflow, making it harder to get a lot of flavor out of....... But it can be done with the right build
For a flavor build on mine I use a dual Clapton..... Results.... Amazing
- Status
Similar threads
