PrecisePlus configuration

[Jacoji]

I have been waffling between PrecisePlus or per-ordering an ELA. I'm an instant gratification kind of girl so I'm leaning toward the PrecisePlus (nothing says I can't get an ELA For my summer birthday if I already have a PrecisePlus). I'm looking for some encouragement or dissuasion from my choices.

18350 2-Tone

• I have 4 of the batteries already and a compatible charger (no 16340 option for my charger)
• Like the shorter size and really long battery life is not a big concern

Kick

• Not super-interested in a Kick currently and realize that I will need an add-on if I go with the 18350 (no room in the tube for a battery and a kick)
• Hopeful for a shorter Kiklet or an integrated Kick top cap if I decide I want a Kick in the future

Slanted Top Cap

• I just ordered a Z-Atty Pro for the Provari and sounds like this will fit a slant cap with a slight gap
• Will continue to use some carto tanks on hand that will fit/look better with a slanted cap

Spare Kiklet Top Cap

• More flexibility and a seamless fit with other flat-bottom tanks.

Anything else I should be considering for my purchase? I just spent a lot of time in the Picture Thread.

Thanks!

 

[zippersnapper]

How "Instant" is your instant gratification need?

I did notice at ProVape the Zen is available..your very lucky to have scored that, in itself..

I bet in 30 min, they will be gone...

 

[Jacoji]

Ahh! - too instant to be satisfied by 18350 being out of stock. That cursed message after Add to Cart.

I don't need anything immediately - just wanted something sooner than 6-8 weeks out for ELA.

I noticed the Zen was most often sold out and read here that they sell out fast when they do become available so when I saw it in stock I snatched one up. Playing with that might tide me over for a bit.

 

[vaptamist]

The P+18350 two-tone with a flat cap is my go-to mechanical PV. I have a kiklet, but was not having much luck with enough battery life - but I recently read that at some point, they changed the cutoff voltage for the kick - both of my kicks were purchased within minutes of the very first batch released, so I was pretty sure that they had the higher voltage cutoff. My 18350 batteries are pretty well used, also. I decided to order a "new" kick, and a new 18350 battery to try out with it, and it made a WORLD of difference. Once I installed it in my kiklet, I cranked it up to 10 watts and it hasn't left my P+18350 since it arrived on Saturday. It's definitely a nice combo.

As far as any other super-t products to purchase with it, I can't think of anything.

Concerning the ELA - I'm probably going to purchase one at some point, particularly once the add-on's start getting produced (306 feeder, integrated atomizer tank, DNA20 add-on), but for now, I couldn't be any happier with the P+18350.

Not sure if this helps, but wanted to chime in.

 

[vaptamist]

Ahh! - too instant to be satisfied by 18350 being out of stock. That cursed message after Add to Cart.

I don't need anything immediately - just wanted something sooner than 6-8 weeks out for ELA.

I noticed the Zen was most often sold out and read here that they sell out fast when they do become available so when I saw it in stock I snatched one up. Playing with that might tide me over for a bit.

Aw, bummer Well maybe David can chime in about the next batch of P+ and when they'll be available. It may just make sense to go ahead and get the ELA if it's going to be awhile.

 

[Jacoji]

I'm not too optimistic on the PrecisePlus being back in stock any time soon. Sounds like the priorities at Super T are the Shockwave and the ELA now that "the new machine" is in.

 

[zippersnapper]

I'm not too optimistic on the PrecisePlus being back in stock any time soon. Sounds like the priorities at Super T are the Shockwave and the ELA now that "the new machine" is in.

Im sure things will speed up now that David has the RR of CNC's in house.
Myself, it took 6 months of stalking before I scored my P+. It was worth the wait however. The poor folks who ordered the Shockwave have been waiting since April I belive of last year, AND I know it will be worth their wait....

If David makes any more Shockwaves, which last I heard was out of the question, I'm going to half to start stalking again....for sure...

If Super T ever puts out some "scratch & dent" for sale...BUY IT. It's pretty much flawless..

 

[forcedfuel50]

I have been waffling between PrecisePlus or per-ordering an ELA. I'm an instant gratification kind of girl so I'm leaning toward the PrecisePlus (nothing says I can't get an ELA For my summer birthday if I already have a PrecisePlus). I'm looking for some encouragement or dissuasion from my choices.

18350 2-Tone

• I have 4 of the batteries already and a compatible charger (no 16340 option for my charger)
• Like the shorter size and really long battery life is not a big concern

Kick

• Not super-interested in a Kick currently and realize that I will need an add-on if I go with the 18350 (no room in the tube for a battery and a kick)
• Hopeful for a shorter Kiklet or an integrated Kick top cap if I decide I want a Kick in the future

Slanted Top Cap

• I just ordered a Z-Atty Pro for the Provari and sounds like this will fit a slant cap with a slight gap
• Will continue to use some carto tanks on hand that will fit/look better with a slanted cap

Spare Kiklet Top Cap

• More flexibility and a seamless fit with other flat-bottom tanks.

Anything else I should be considering for my purchase? I just spent a lot of time in the Picture Thread.

Thanks!

Good morning Jacoji! I still plan to make an integrated screw on module type Kick arrangement for the P+ series, which since it's not universal fit like the Kiklet and replaces the top cap, will save several MM in length.

I do have a PrecisePLus 18350 slant cap if you need one. Shoot me an email to supertmanufacturing@yahoo.com if you'd like it.

I'm not too optimistic on the PrecisePlus being back in stock any time soon. Sounds like the priorities at Super T are the Shockwave and the ELA now that "the new machine" is in.

Once we get familiar with the machine and all tooled up, no projects will really need to take priority, as this machine is more then capable of making all the parts we need, and several other mod makers parts too if needed! We'll have the ability to do several projects all in one week, not like the days of old where only one project could be done every several months.

 

[Riverboat]

How "Instant" is your instant gratification need?

I did notice at ProVape the Zen is available..your very lucky to have scored that, in itself..

I bet in 30 min, they will be gone...

No they finally flooded the market enough with ZAPs.. Been up since last Friday and their still available.. I use to own one...sold it-to heavy/bulky with an airy draw.... Looks terrible on a P+ and must be stood upright or they leak....

 

[vaptamist]

Pretty sure the only thing I would ever give up my P+18350 for would be a P+18350 made out of Titanium

 

[Jacoji]

No they finally flooded the market enough with ZAPs.. Been up since last Friday and their still available.. I use to own one...sold it-to heavy/bulky with an airy draw.... Looks terrible on a P+ and must be stood upright or they leak....

Duly noted. Already ordered so at least with the slant cap it will transfer between the 2 devices even if it won't win any prizes for beauty - and require a drilled-out block of wood to keep it tip up. I'm sure I will continue to research and pick up other RBAs once I've had some experience with them. I was probably a little hasty in my decision to purchase a ZAP.

 

[grandmato5]

I love my Zap on my Precise + 18350. I have the flat top P+ and the Zap fits well on the flat top using a 510 to 510 shorty connector. Its true, cant lay a Genesis atty on its side or it will leak, but that's not a problem for me as I don't lay my APV's on their side anyways.

 

[zippersnapper]

I still plan to make an integrated screw on module type Kick arrangement for the P+ series, which since it's not universal fit like the Kiklet and replaces the top cap, will save several MM in length.

That, I will be stalking for. I just purchased a Kick for my P+. Zap-never cared for it..I love to many different juices..Kanger T3's ?
Have 15 now, and another 45 more comming in a Co-Op. Would I love to have my P+ working with them ? Thats a major understatement...to be sure. Recessed outside eGo threaded top cap ? Prayers would be answered.

Super T "in house made" 510 to eGo adaptors with American machine shop quality threads would be killer as well..

 

[Riverboat]

I love my Zap on my Precise + 18350. I have the flat top P+ and the Zap fits well on the flat top using a 510 to 510 shorty connector. Its true, cant lay a Genesis atty on its side or it will leak, but that's not a problem for me as I don't lay my APV's on their side anyways.

That Zap weighs as much or than your P+18350....plus with the bottom button design of a P+ it can easily tip over IMO...

 

[vaptamist]

What's wrong with top-heavy?!

 

[Jacoji]

What's wrong with top-heavy?!

Hear, hear! (I always thought this was "here, here", just learned it is a shortened version of "Hear ye, hear ye". Stupid homophones.)

I also have a couple of HH.357's in the post so the ZAP won't always be on it - I just want the flexibility. Even if I have to start with an ugly drilled-out piece of scrap-wood on the side table I will keep it tip up. This setup wouldn't be for mobility.

@vaptamist - Is that an 18350 with a ZAP in your signature photo?

 

[vaptamist]

@vaptamist - Is that an 18350 with a ZAP in your signature photo?

It's not - it's a Titanium Zenesis Standard. I actually don't have it anymore but I've been too lazy to pick a new photo.

 

[Jacoji]

shipping confirmaTION
PrecisePlus here on MonDAY
Temon arrives toDAY

(to be sung and danced as a conga)

 

[Jacoji]

... and gratified!

Pictures up at http://www.e-cigarette-forum.com/forum/super-t-manufacturing/108893-official-super-t-picture-comment-thread-51.html#post8408668.

Love, Love, Love it!

 

[Royaldrunker]

i see a lot of people with the 18350 configuration

anything wrong with the 18650 as per size and bulk