probably the best electronic from TayVoy

[szczuro]

so one more time
I'v got a short vacation
hope this time, more users can read this post, 'bout probably the best electronic from Poland

this module U can find in Gepetto, TVP, and in near futer mod TayWoy Mod TayVoy « TayVoy
but the improved version

and of course without any mods*, so U can buy, and use whenever U want


short description of actuall version tayvoy-u-7s Regulator TayVoy-U-7s « TayVoy

now u can find 4 different programs and choose /*in new version - only available with TayVoy mod - 'll be 9 programs/
for simple visualization
time = 8 seconds
0,5 second - time unit
100% - nominal voltage of

characteristics of heating in comparison to the set voltage

A1 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%
A2 0% , 25%, 75%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%
A3 120%, 120%, 120%, 120%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%
A4 100%, 100%, 100%, 100%, 120%, 120%, 120%, 120%, 100%, 100%, 100%, 100%, 100%, 100%, 100%, 100%



IMO ProVape can use this electronic module in their own mods


and planning +5 programs

A5 100, 150, 150, 150, 150, 80, 80, 80, 80, 150, 150, 150, 150, 80, 80, 80

A6 120, 150, 150, 140, 130, 120, 100, 80, 150, 140, 130, 120, 100, 60, 60, 110

A7 100, 120, 140, 150, 130, 110, 100, 100, 120, 130, 140, 150, 130, 120, 110, 100

A8 150, 150, 150, 100, 100, 150, 150, 150, 150, 100, 100, 150, 150, 150, 100, 100

A9 defined by the user



also u can find many cool options
PH - Preheating Liquid
HL - Heating Limit
UT - Voltage treshold - range 5,4 - 5,9


need more infos, just write Q

-----------------------------
for ECF ADMISTRATION - I'm not supplier affiliate/associate
so I don't have to pay to write 'bout sth good
more info through PM
-----------------------------

edit: correct value in A3 - GREEN COLOR

 

[Shel]

szczurio
I have a mod on order, actually in the mail to me which uses this electronics, and I'm eager to try it out.

One suggestion, it would be very useful if this mod could indicate the ohms of any atty or carto attached to the device!

I happen to use that function on my ProVari.

What attracted me to the electronics is the ability to change voltage with the push of a button. I have mods which require turning a dial, and frankly, they become a pain when you want a specific setting. Mods which require a tiny screwdriver, are even more inconvenient.

What I'm NOT sure of is, how useful the added functions will prove to be.

Generally, I set my device to, say, 4.7v, and pretty much leave it there until/unless I'm changing juice, or changing the atty/cart. Sometimes I do want a warmer/stronger vap, or a cooler vap, and change settings accordingly.

Not sure if I'll find it beneficial to have the voltage, say, 150 % of my setting for two seconds,(in setting A3) then switching to my original setting. So, I assume, if I set it to 4v, and my device is set to A3, the voltage would be 150% of 4v, or 6v (?) for two seconds, then change back to 100% of my setting, 4v, for the remainder of the time I hold the button down?

Is this correct?

One other question...
When you first press the switch (button) to vap, is the current battery charge what is displayed?

Thanks!

 

[szczuro]

szczurio
I have a mod on order, actually in the mail to me which uses this electronics, and I'm eager to try it out.

good

One suggestion, it would be very useful if this mod could indicate the ohms of any atty or carto attached to the device!

can't have everything

What attracted me to the electronics is the ability to change voltage with the push of a button. I have mods which require turning a dial, and frankly, they become a pain when you want a specific setting. Mods which require a tiny screwdriver, are even more inconvenient.

for me also

What I'm NOT sure of is, how useful the added functions will prove to be.

mastery - it takes few minutes

Generally, I set my device to, say, 4.7v, and pretty much leave it there until/unless I'm changing juice, or changing the atty/cart. Sometimes I do want a warmer/stronger vap, or a cooler vap, and change settings accordingly.

U can changes voltage at any time

Not sure if I'll find it beneficial to have the voltage, say, 150 % of my setting for two seconds,(in setting A3) then switching to my original setting. So, I assume, if I set it to 4v, and my device is set to A3, the voltage would be 150% of 4v, or 6v (?) for two seconds, then change back to 100% of my setting, 4v, for the remainder of the time I hold the button down?
Is this correct?

correct value in A3 is 120% - green color above - sorry for my mistake

set 4V and A3 program
first 2 seconds is 4,8 and after set value 4v

important Note - on the display/pressed button/ for a whole time, U see te value of battery voltage of the load

One other question...
When you first press the switch (button) to vap, is the current battery charge what is displayed?

standard settings of voltage is 4,2 or 4,0
stanby mode - voltage of your bettery
press button - battery voltage of the load - LR lower value, HR higher value - joke U know 'bout this

Thanks!

U'are welcome
hope are clearly or not

 

[seantex]

so can I buy these electronics to install in my own mod?

 

[szczuro]

so can I buy these electronics to install in my own mod?

yes
contact info - find here Regulator TayVoy-U-m « TayVoy

 

[jimbalny]

Wish there was some more information in english on price and ordering, google translate isnt working too great on this site for me.

 

[szczuro]

Wish there was some more information in english on price and ordering, google translate isnt working too great on this site for me.

just write email to muzyktaywoy@gmail.com
good luck

 

[alexp843]

looks like price is ...136 Polish zlotys = 42.7969 US dollars

 

[urquidezj]

Not bad if u ask me will be ordering soon.

 

[asdaq]

I need to think up a mod to house this right first. Something like two 18350's, this and the Gtank-US, hmmm, no extra switch needed.

 

[urquidezj]

Asdaq, its from poland eplain to me this is a switching regulator? It needs stacked batts right? I can make a mod for it on a lathe to take two 18350 if tuats the case.

 

[asdaq]

It's a PWM regulator and takes 2 stacked batts and is programmable through the single button. You could almost say it's the provari equivalent of a two cell setup. Setting it to pulse occasionally to keep the coil warm is cute.

 

[urquidezj]

Are they worth it tho? Will they perform good so I can have a backup for provari

 

[Shel]

Setting it to pulse occasionally to keep the coil warm is cute.

asdaq
What exactly does warming the coil DO?

When I hit the switch, the atty turns on and, as I understand it, goes to something like 180 degrees in seconds... no? (Not sure of the exact temp, and obviously, it varies depending on the voltage setting, but the idea is the same)

So what do I gain by pre-warming the atty? Does it vap faster?

Sorry... I just don't see what advantage it provides.

 

[asdaq]

It is something like standby mode. Imagine every 15 seconds your atty fires for one second to keep it warm, so that when you do take a hit the atty is always pre warmed. These are just estimates with the formula, but with PWM and timing this is simple to program into it.

sent from my HTC genisis using Tapatalk