Question about Vamo V5

[Dissonance]

So I know the Vamo V5 can go from 3-15 watts, and 3-6 volts... I think I saw on a spec sheet it has a limit of 5 amps, and won't fire an atomizer under 1.2Ω.

My question is... If you have a 1.2Ω atomizer and set it to 6 volts, will it fire at the full 6 volts? (Aka 30 watts)

 

[edyle]

Details:

•mod: VAMO V5
•Atomizer: CE4
•0.75" OLED display screen showing menu, function and selection
•Variable wattage - can be adjustable from 3.0W to 15.0W (in .5W increments)
•Variable voltage - can be adjustable from 3.0V to 6.0V (in .1V increments)
•Maximum current output: 5A
•Reverse battery protection, over current protection
•Check atomizer resistance
•Check voltage, wattage and current
•Thermal Monitoring
•Time limit protection function
•Low voltage, low load (resistance) and short circuit warning
•Bottom vent hole
•510/eGo threading connector
•Compatible with 510 and eGo threaded atomizers/clearomizers/cartomizers with resistance 1.5-5.0ohm
•Can be powered by 1*18350 battery/2*18350/1*18650 battery
•Battery charger supported battery length: 30-69mm
•VAMO mod supported battery length: Max. 70mm

Well there's a 5amp output limit.

But there's a 1.5 ohm limit; so no: no 30 watts.

so i guess the question is what happens at 6 volts and 1.5 ohms; that corresponds to 24 watts.

 

[Dissonance]

Well there's a 5amp output limit.

But there's a 1.5 ohm limit; so no: no 30 watts.

so i guess the question is what happens at 6 volts and 1.5 ohms; that corresponds to 24 watts.

Thank you Wasn't sure if it would automatically limit itself to 15W for some reason or not.

Also, what do you mean by 1.5Ω limit? I'm using a 1.2Ω coil atm (hence the question) and it's firing fine :O Am I missing something? I know it won't fire anything below 1.2Ω (The resistance just shows up on display and it does nothing) but yeah.

 

[edyle]

Thank you Wasn't sure if it would automatically limit itself to 15W for some reason or not.

Also, what do you mean by 1.5Ω limit? I'm using a 1.2Ω coil atm (hence the question) and it's firing fine :O Am I missing something? I know it won't fire anything below 1.2Ω (The resistance just shows up on display and it does nothing) but yeah.

Bolded it in the specs just now:

supports 1.5 ohms to 5.0 ohms.

So that means if it sees lower than 1.5 ohms it probably gives the LowV error message.

Or, it could also mean that below 1.5 ohms or above 5.0 ohms, the full range of settings may not apply.


It's often not so clear how a mod will perform at the extremes.

I dryburn my coils by setting my vamo to 3 watts; but for my typical 2 ohm coilss that works out to 2.5 volts; but I doubt my vamo puts out 2.5 volts; but maybe; one day I'll check it when I have a dripper-- well maybe not because its a pwm signal and not a constant dc; oh well.

 

[classwife]

Moved to Variable Voltage APV Discussion from APV Discussion

 

[Tbev]

That's correct it will do whatever comes out to the amp limit, with acception of going below the Ohm limits I think it's actually 1 .3 but yule better off wrapping a 1.5 ohm coil.

Sent from my Transformer TF101 using Tapatalk

 

[4redstars]

There is a DNA 30 Vamo for preorder out there...around 70 dollars.

 

[Tbev]

That's possibly a great device possibly pos, depending on who's making it

Sent from my Transformer TF101 using Tapatalk

 

[4redstars]

It's KSD, I believe the original makers of the Vamo