QZI mods and other "atrocities"

[UnFettered_Soul]

The draw is a little stiffer than I'm use to.
Not a bad thing, or a complaint, just different.

I like the fill hole screw, but my eyes aren't what they use to be, so it was hard to get it back in.
I may try it without the screw next fill up to see if it makes a difference with the draw.

I would have moved the engravings up.... only because I feel like I'm going to wear them off the way my hand falls.
However, the switch is light enough that I can hold it towards the bottom and push the switch with my ring finger, so I'm not holding or rubbing against the engravings.

It's not the lightest PV I have, but it's not overly heavy either.
Lighter than my ProVari Mini/ZAP combo, but about the same as my Zen Standard. (If that helps anyone)

It is a fingerprint magnet. LOL But I have soft cloths I can wipe it off with.

All in all, I'm happy with the purchase.
I'm sure JunkyRock will do a video review, and a much better job than I just did.

I would purchase again. Once I have my pennies saved up again.
The shipping was surprisingly fast, considering it came from another country.

Thanks again Tommy!

 

[UnFettered_Soul]

Thanks for coming on Junky's show Eagle....
it was good to see you.

 

[Eagle Talon]

Thanks for coming on Junky's show Eagle....
it was good to see you.

I have the honor!!

 

[Eagle Talon]

MEGATRON USERS! ADJUST YOUR BUTTON PROPERELY!

I'd like to kindly ask Megatron users, please adjust your button properely!

Megatron button's switching path must not be shorter than 1,5-2 mm. Lower limit is 1,5 mm, neve make it shorter! Of course it can be longer!
After you adjusted your button spike, please pull down the insulator ring firmly!

Thank you very much!
Kind regards,

 

[UnFettered_Soul]

MEGATRON USERS! ADJUST YOUR BUTTON PROPERELY!

I'd like to kindly ask Megatron users, please adjust your button properely!

Megatron button's switching path must not be shorter than 1,5-2 mm. Lower limit is 1,5 mm, neve make it shorter! Of course it can be longer!
After you adjusted your button spike, please pull down the insulator ring firmly!

Thank you very much!
Kind regards,

Do you have pictures or a video, or even written instructions for this?

 

[bk78]

MEGATRON USERS! ADJUST YOUR BUTTON PROPERELY!

I'd like to kindly ask Megatron users, please adjust your button properely!

Megatron button's switching path must not be shorter than 1,5-2 mm. Lower limit is 1,5 mm, neve make it shorter! Of course it can be longer!
After you adjusted your button spike, please pull down the insulator ring firmly!

Thank you very much!
Kind regards,

Ya a little how to guide would be good. And why must we do this? Is there problems that can occure if we don't?

 

[Eagle Talon]

Ya a little how to guide would be good. And why must we do this? Is there problems that can occure if we don't?

Can be adjusted to the size of the battery.

 

[UnFettered_Soul]

I think I figured it out....
The entire switch comes apart.
I was able to move the brass colored piece that's inside the spring. It seems to screw/unscrew.
I unscrewed it a bit, put everything back together and it's working fine.

I think it was working fine before I did that though. LOL
But it does wobble a bit less now when set on end with the switch unlocked.

On my second tank and the taste and vapor are improving.
I'm still liking my new PV.

 

[UnFettered_Soul]

Here's a helpful video.
Shows quite a bit about these PVs.

 

[aeb]

Anyone take their glass tank off yet? I can't get mine to budge. Every time I try I get scared that I'm going to crack it lol. Great device though. Hits like a freight train.


Sent from my iPhone

 

[bk78]

I'm a idiot lol

 

[UnFettered_Soul]

Anyone take their glass tank off yet? I can't get mine to budge. Every time I try I get scared that I'm going to crack it lol. Great device though. Hits like a freight train.


Sent from my iPhone

I have not, but JunkyRock13 mentioned on his last show that he has.
He also found it to be a tight fit.
He said he ran it under hot water and it was easier to get off.

Remove both top o-rings from where the cap sits.
Run it under hot water, and gently grip while twisting up.
Using juice on the tank o-rings will help get it back on.
Gentle grip and twisting motions..... either direction.

 

[UnFettered_Soul]

Is there any pictures out there in the world of the full size atty? Tommy?

A few posts back bk, I posted a couple.

 

[bk78]

A few posts back bk, I posted a couple.

I don't know how I missed that. Duh me

 

[UnFettered_Soul]

I don't know how I missed that. Duh me

I've managed to miss entire pages, see something quoted, and realize I missed the whole darn thing. LOL

 

[Thorbear]

My wait is over, I received mine today Saw from the tracking that it came to my local post office at 8am this morning, so I had a long day at work in anticipation of getting it.
Nice touch that it was already set up with a wick and coil. I metered it at ~2 ohms, so it is a bit higher resistance than I normally use on an unregulated pv.
Filled it up with some juice, and I have to say I am getting nice flavor from the start. I like the stiffer draw that this has, it sits nicely between the draws of my iHybrid and the cobra that I have been using the most lately. Will be running a tank or two through it like this, before trying my usual 4/3 twisted 32g coil that i normally use.
The switch is really nice, stiff enough spring to set it down without firing and doesn't wobble all over the place, but still easy to push.
My initial impression : I am happy with my purchase.

Thank you Eagle and QZI

 

[dredd0606]

Got mine today too...beautiful mod. Make no mistake, its a massive mod, but its beautiful. The engraving is top notch, the button is smooth to screw and unscrew, adjustable throw on the button, relatively easy button press. Wick and coil came wrapped perfectly, metered at 2.1 ohms, so a little higher than I like, but I just filled it and went. For me the draw is a little too tight, so I may open it up a bit, I'm undecided so far. The only complaint I have is that the 510 drip tip hole seems too small for every one of my drip tips, so I was forced to use a crappy plastic one from a smoktech tank. Other than that, its a beautiful fingerprint magnet (make one in a brushed finish and I'll buy it too!).

 

[Thorbear]

Nice, congrats.
I had to go through my drip tips too, but i found a couple that fit perfectly.
Currently working on covering it in finger prints aswell

 

[bk78]

Received mine today too. All my drip tips fit no problem. The draw is too tight for me so that my job tomorrow. The picture shown is with my trap tank it's a perfect fit. Great job on the fingerprint magnet Tommy

 

[bk78]

Although I do have to replace my o-ring. It's leaking already. I have the worst luck with leaking brand new ihybid I bought last week leaked all over the place too.