Simply Mods Creations presents: The Vamo Schrinked parts from Tournoulette...

[rataplan]

Hello everyone, as a new Belgian ''e-cigarette modding '' company we would like to introduce ourselves on this forum.
Because of the great demand for the components of the Vamo shrinked mod parts by the modder '' Tournlounette '' of Canada we would like to offer verry soon complete sets in aluminum for the Vamo, including Bottom Part,Top Part, nuts, threaded rods, and threaded rod cover tubes, and soldered+ pole.
Follow us on our website for more information.
Once the parts follow, and mounted, the photos are online. AlsoThank you very much ''tournoulette'' for the plans, they are even further adjusted.
Price for 1 set complete 47$ including shipping to the US and Canada.


Regards,

Serge Poplemon from Simply Mods Creations Belgium



Website: http://www.Simply-Mods-Creations.be

 

[Tourlounette]

Hello,
I realy appreciate the fact that you gave me credit for the design.
Also very glad that you go in production since it was not possible for me to do so.
Looking at your website you seem to be an "artisan" that's also a thing that make me glad.
Your list price is in the good range of the value, perfect!

So good luck, do a good job and I'll be glad to refered to people to you!

A lot of other person contribute in the inspiration, in particular I would like to highlight the works of "Asdaq"!

 

[rataplan]

Hello Tourlounette,
Thank you very much, and if in the future I have a re service can make it, please let me know.
Regards,
Rataplan

 

[northhar]

Very nice to see that this is going to be available soon..

 

[rataplan]

Very nice to see that this is going to be available soon..

Thanks northhar, normally this would be around 22 April, info will follow.
Greetings,
rataplan

 

[rataplan]

Hello,
today the following trial ''bottom'' and ''Top'' part through photo obtained, the test pieces are now almost at its final point.
It's now a matter of + - 10 days for the production will start after the work pieces are mounted and approved by us.
updates to follow.


regards,
rataplan

 

[Disconnect]

Looks awesome! And I have a vamo already separated and ready for it

 

[asdaq]

Good to see such fine progress, what might be the price for shipping in the EU?

 

[rataplan]

Good to see such fine progress, what might be the price for shipping in the EU?

Hello asdaq, total price including shipping within Europe is 36 €
regards
rataplan

 

[anavidfan]

Do you modify things like atomizer tanks such as I have an Odysseus and would like to have some lines added to the tank to match my new PV that is coming? or giving a brushed finish to polished stainless steel?

 

[Tourlounette]

Hello,
today the following trial ''bottom'' and ''Top'' part through photo obtained, the test pieces are now almost at its final point.
It's now a matter of + - 10 days for the production will start after the work pieces are mounted and approved by us.
updates to follow.


regards,
rataplan

Just want to say that have modify my original plan cause it was large enough to be able to use a "terminator" attys.
Just need 1mm more.
So take care to check it before going into production.

 

[rataplan]

Hi, unfortunately not, I own some modifications to a V-Core clearomizer made but that's just a paint job and what decorations like this

 

[rataplan]

Just want to say that have modify my original plan cause it was large enough to be able to use a "terminator" attys.
Just need 1mm more.
So take care to check it before going into production.

Right Tourlounette, as I have noted,the plan is adjusted, thanks for the feedback

 

[Innocuous]

I've been following the Shrinking Vamo for awhile. Loving it.

Question, however: I can't tell from the pictography.. Is the midsection press-fit like the top? Or, did you need something like a pipe-cutter or hacksaw to part controls from battery-space?

Thanks!

 

[PinoyBoy]

I've wanted a Zenesis Sidewinder ever since laying my eyes on it. This might just be what I've been looking for.

 

[rataplan]

I've been following the Shrinking Vamo for awhile. Loving it.

Question, however: I can't tell from the pictography.. Is the midsection press-fit like the top? Or, did you need something like a pipe-cutter or hacksaw to part controls from battery-space?

Thanks!

Hi, I supply them with the positive wire already soldered, the space for the thread is already machined , the picture was a trial piece that you see.
Regards,
rataplan

 

[Innocuous]

Thanks.

However I meant the tube disassembly, as shown in all the original posts, (by Tourlounette, I think). The question is:

Is the tube nearest the control-section is a press-fit to wiggle off, (like the top), or is it homogenous with the control-tube, (either welded together or the 'seperation line' is just a cut)?

The reason I ask is to ascertain the complexity of the mod and tools required: I know I will not attempt such a thing until I am desperate or have a replacement Vamo in the other hand ;-)

 

[rataplan]

Thanks.

However I meant the tube disassembly, as shown in all the original posts, (by Tourlounette, I think). The question is:

Is the tube nearest the control-section is a press-fit to wiggle off, (like the top), or is it homogenous with the control-tube, (either welded together or the 'seperation line' is just a cut)?

The reason I ask is to ascertain the complexity of the mod and tools required: I know I will not attempt such a thing until I am desperate or have a replacement Vamo in the other hand ;-)

Hello, all you have to do is with the original Vamo: take the vamo with both hands in half and wiggle up and down so that the tube slides out in 2 halves, the battery compartiment is now ready for mounting. The other part, the control unit must be edited. You have to remove the bottom edge of the tube, this is thinner than the tube and is easy to remove. Than barn you the bottom smooth with sandpaper, and solder you the + Pole on the print head , isolate the solder, and you can mount the 2 pieces, control head and battery tube. I will shortly the necessary steps shooting and posting here.
Regards
rataplan

 

[Absintheur]

I've wanted a Zenesis Sidewinder ever since laying my eyes on it. This might just be what I've been looking for.

You can buy the Zen Sidewinder with a 510 connector now...wouldn't be variable tho...

 

[Innocuous]

AH-hah!

OK, thanks. I think I envision the disassembly, now - will appreciate the pictorial when posted, thank you!