smok Vapor Chaser tank (VCT) A1, 3.8 ml Adjustable Sub Ohm Coil Clearomizer
The Vapor Chaser tank (VCT) A1 is a new sub ohm clearomizer by Smok. The VCT A1 is made of stainless steel and features adjustable airflow control: easily customize your draw by turning the airflow control ring at the base of the tank. The sturdy pyrex glass tank has 3.8 ml capacity and can withstand even harsh e-liquids.
The VCT A1 uses A1-core coils which offer great flavor and vapor production! They feature a single vertical coil and use organic cotton. These coils are special because they utilize Smok's Adjustable Liquid Feed (ALF) technology: by twisting the hole cover up or down you can increase or decrease the e-liquid intake to the coil depending on the viscosity of your juice. With A1-core coils, you can get the best out of your thinner PG or thicker VG based juices!
Changing the coil is easy: simply unscrew the base of the VCT A1, unscrew the old coil and screw in a new one. To fill the VCT A1, remove the base, tilt at a slight angle and fill with 3.8 ml of e-liquid (be careful not to get any e-liquid down the center tube.) Screw the base back on and allow a few minutes for the e-liquid to saturate the coil. Please make sure to prime a new coil by dripping a few drops of e-liquid down the center of the coil. If the coil is not properly saturated, it may burn.
The VCT A1 has a 510 connection and a removable wide bore 510 drip tip.
Features:
1 x Vapor Chaser Tank (VCT) A1 (pre-installed with 0.5 sub ohm A1-core head / 15-30W range)
1 x Extra A1-core head (0.5 sub ohm / 15-30W range)
1 x Spare Pyrex glass tube
2 x Spare o-rings
1 x User Manual
1 x Nice packing box to store the tank when not in use
PLEASE NOTE: Please only use the sub ohm (0.5 ohm) A1-core coils in the VCT A1 with devices capable of handling sub ohm coils. If using a mechanical mod, please only use High Drain batteries with a high amp limit; if using a variable power mod, please use High Drain batteries in a device capable of putting out 20W or higher. NEVER use sub ohm coils on an eGo battery or a device unequipped to support sub ohm coils. It is for your safety!
To ensure that the A1-core heads are thoroughly saturated and do not burn, Smok recommends dripping a few drops of e-liquid into the center of the coil head before using, as well as setting the tank aside for a few moments after filling with e-liquid. Please take the time to read the included User Manual for a detailed description on the proper use of this unit.
Dimensions: Height 66mm (2.5") / Diameter 22mm (0.86")
Replacement A1 coils are also available:
The Vapor Chaser tank (VCT) A1 is a new sub ohm clearomizer by Smok. The VCT A1 is made of stainless steel and features adjustable airflow control: easily customize your draw by turning the airflow control ring at the base of the tank. The sturdy pyrex glass tank has 3.8 ml capacity and can withstand even harsh e-liquids.
The VCT A1 uses A1-core coils which offer great flavor and vapor production! They feature a single vertical coil and use organic cotton. These coils are special because they utilize Smok's Adjustable Liquid Feed (ALF) technology: by twisting the hole cover up or down you can increase or decrease the e-liquid intake to the coil depending on the viscosity of your juice. With A1-core coils, you can get the best out of your thinner PG or thicker VG based juices!
Changing the coil is easy: simply unscrew the base of the VCT A1, unscrew the old coil and screw in a new one. To fill the VCT A1, remove the base, tilt at a slight angle and fill with 3.8 ml of e-liquid (be careful not to get any e-liquid down the center tube.) Screw the base back on and allow a few minutes for the e-liquid to saturate the coil. Please make sure to prime a new coil by dripping a few drops of e-liquid down the center of the coil. If the coil is not properly saturated, it may burn.
The VCT A1 has a 510 connection and a removable wide bore 510 drip tip.
Features:
- A1-core sub ohm coils with Adjustable Liquid Feed (ALF) technology
- Adjustable Airflow Control
- 510 connector
- Stainless Steel construction
- Pyrex Glass Tank for protection from harsh liquids
- Capacity is 3.8 ml
1 x Vapor Chaser Tank (VCT) A1 (pre-installed with 0.5 sub ohm A1-core head / 15-30W range)
1 x Extra A1-core head (0.5 sub ohm / 15-30W range)
1 x Spare Pyrex glass tube
2 x Spare o-rings
1 x User Manual
1 x Nice packing box to store the tank when not in use
PLEASE NOTE: Please only use the sub ohm (0.5 ohm) A1-core coils in the VCT A1 with devices capable of handling sub ohm coils. If using a mechanical mod, please only use High Drain batteries with a high amp limit; if using a variable power mod, please use High Drain batteries in a device capable of putting out 20W or higher. NEVER use sub ohm coils on an eGo battery or a device unequipped to support sub ohm coils. It is for your safety!
To ensure that the A1-core heads are thoroughly saturated and do not burn, Smok recommends dripping a few drops of e-liquid into the center of the coil head before using, as well as setting the tank aside for a few moments after filling with e-liquid. Please take the time to read the included User Manual for a detailed description on the proper use of this unit.
Dimensions: Height 66mm (2.5") / Diameter 22mm (0.86")
Replacement A1 coils are also available:
