I am soo love with my billet box.. It's pure perfection in every way... Surpassed my expectations by miles.. I will post pictures later, the princess is grumpy 
- Status
Sorry guys, a little late to the party. Just got home and about to fill it up with juice for the first time
GeeeeesSH Silent!!!!!!!! You had us all WORRIED!!! FINALLY!!!!!! ;-)
Video at 11?
If you have control over the size of the hole, a good first try would be somewhere between 1mm and 2mm. Once it's in the tank, check to see if you're getting flow into the cartomizer by pushing on the face of the BB tank (for a freshly installed carto) and/or taking a hard draw on the carto and looking in the tank immediately after - in either case you're looking for bubbles from the holes.
If you have good bubbles, chances are good that the hole(s) are big enough. If you find the carto goes dry from time to time, add another hole next time. Don't want to go overboard to the point of flooding the carto, though.
If you don't get bubbles, or have to draw really hard to get them, the hole isn't big enough -- and adding more probably won't help. Try making slightly bigger holes, or if your punch can't make bigger holes try thinning the liquid with a bit of distilled water - maybe 5% of total volume to start, just enough to thin it without affecting flavor too much.
Hope this helps!
This is my first time using a carto tank, also. It's not bad and I think I'll get used to it pretty quickly. Never liked that slight 'wooly' taste, though.
Any tips on less-messy ways of draining the tank?
Any tips on less-messy ways of draining the tank?
GeeeeesSH Silent!!!!!!!! You had us all WORRIED!!! FINALLY!!!!!! ;-)
Lol possibly, might make one
Right now I'm dealing with my first carto from Ikenvape which is tasting burnt as hell. I primed it properly too, needle filled :/
Switching to a Boge now lol
when i decided i didnt like the juice i used, i pulled the carto down from the bottom, and then put a needle tip in the top tank hole and sucked out the juice.
Lol possibly, might make one
Right now I'm dealing with my first carto from Ikenvape which is tasting burnt as hell. I primed it properly too, needle filled :/
Switching to a Boge now lol
my first boge did that, like 10 seconds of good vape then ruined. second one going ok now. i might need to waste a box lol
I decided on NLV GOLD!
Also, I wanted to be cool with a knife pic too.
Sent from my SGH-I717 using Tapatalk 2
Also, I wanted to be cool with a knife pic too.
Sent from my SGH-I717 using Tapatalk 2
To switch a carto?
Don't drain it.
Take out the tank and as you slide out the old carto, slide an old one in right behind it.
then in slide your new one and push out the placeholder carto.
Had that problem with my first couple of IKV punched, too, with anything more than 20% VG. Holes too small for most of my liquids.
So, had to slot 'em anyway. After that, though? Have to say, I favor them just a touch more than the Boges.
My first iken was burning for a bit, think it's worth slotting and trying anyway or toss it?
I just popped in a Boge I punched. Definitely working better with 75/25.
My drip tip from DTD doesn't fit
Mine was very tight also. I took off the o ring and sanded the base of the tip. Put the o ring back on and lubed it with juice. Now it fits in snug but okay.
Sent from my SGH-I717 using Tapatalk 2
I know that it is recommended after you prime the carto to press slightly on the face of the tank to get it going. Makes sense to pressurize it a bit. Has anyone tried this and can give us some insight?
Sent from my Galaxy SIII using Tapatalk II
By te way congrats t all of the new BB owners! I will be celebrating my birthday in an hour without a BB. I am patiently waiting for the next sale! On another note happy page 360 BB thread it is the most followed by a lot of folks!
Sent from my Galaxy SIII using Tapatalk II
Sent from my Galaxy SIII using Tapatalk II
- Status
Similar threads
