YEP!!! My last carto did NOT wanna come out! (I had to go and hunt for PLIERS! EEEK!) Finally came out using pliers and brute force!
LOL! Seriously! ;-)
- Status
YEP!!! My last carto did NOT wanna come out! (I had to go and hunt for PLIERS! EEEK!) Finally came out using pliers and brute force!
LOL! Seriously! ;-)
I will wait on reports about the Raven. The last time I ordered from GV was, unfortunately, a LARGE order of stuff that was supposed to be the end-all-be-all of vaping and every single item was pretty much crap. Didn't even put the stuff on PIF as I did't want to burden someone else with it. Swore off ordering from them again unless there are multiple, unequivocal reports of outstanding results, so I'll be interested in hearing how the Raven works out.
Absintheur ... Have you tried the Raven " carto" (more like a little carto sized ATTY - throw away too! 
in your BB yet? Now THIS would be GREAT if it came in a regular size without the flange thingie!! PERFECT for the BB!! A non-tinkering type can hope!!!
in your BB yet? Now THIS would be GREAT if it came in a regular size without the flange thingie!! PERFECT for the BB!! A non-tinkering type can hope!!!
Absintheur ... Have you tried the Raven " carto" (more like a little carto sized ATTY - throw away too!
Read through my last 10 posts in here...lol...
Read through my last 10 posts in here...lol...
GEEESH!!! I was hoping to avoid having to read backwards! LOL!! OooooKkkkkkk ...
Did I also miss that Got Vapes IS coming out with a non-flanged ... In about 2 weeks ... Don't think it's regular size though.
well @2.1 ohms and 4v the Diver is a beast...shave 2mm off the top and trim the flange flush....piece of cake
Awesome. Mine should be here sometime this week. Good to know it's easy to get working in the BB.
well @2.1 ohms and 4v the Diver is a beast...shave 2mm off the top and trim the flange flush....piece of cake
What kind of juice ?vg, ?pg whit Diver
I vape 65vg 35pg what do you use
Last edited:
bounty hunter....amazing amounts of vapor and very easy to draw...pretty close to my AGA...taste is deeeeelicious
Whew, glad to hear I'm not the only one who had a bitsy bit of a prob removing the carto. Lesson learned.
Read through my last 10 posts in here...lol...
Welp, so did ya???
And Bounty Hunter is 65/35 I think, right? Pretty sure that's what my jugs say.
the only thing that concerns me about the diver and I have two here - and one in a tank and set-up properly it vapes like a champ if a tad gurgly when left for a while - but I digress - the one thing that concerns me at the moment is that the air tube positive pin part is made of what looks like Brass - this gets hot (due to electricity) and is in constant contact with the juice and I'm concerned that this poses a health concern - as generally exposed brass is considered a no-no in vaping....
I need to check up on this a bit more....
I need to check up on this a bit more....
Oh and make sure that you've cleaned your diver PROPERLY before using it!
Diver Atomiser - Dirty Tube. - YouTube
Diver Atomiser - Dirty Tube. - YouTube
Where is it in contact with juice? Just down the little central hole of the ceramic cup? Otherwise the cup is pressed into the SS base piece, right?
It's actually pressed into what appears to be Delrin - and I've observed that without NR tails on the coil the tails WILL melt the Delrin - which is ANOTHER concern of mine - hence why I'm using NR tails on it from here-on-in
Yes the air pipe only contacts the juice at the top at the bottom of the ceramic cup but nevertheless it is still in contact with juice and you are inhaling air sucked through it when it gets hot.
Got the diver, took a little work to get it to fit (sandpaper and 5 minutes). Totally worth it this thing screams now. The difference from cartos is so drastic I can't even put it into words.
Also premades exist (same as killer) so just have to do a little sanding and you're good to go.
Also premades exist (same as killer) so just have to do a little sanding and you're good to go.
- Status
Similar threads
