Top airflow BF attys?
- Thread starter brickfollett
- Start date
- th_trl_thread_readers 0
- Status
Cool, thanks, can you comment on the rogues airflow before i shoot him a message?
I got a Rogue from Chowder's first run. It's pretty airy. Better suited for lung hitters looking for big airflow than mouth to lung vapers. The AFC doesn't work very well in closing down the airflow. You can sand down the top piece, which is a challenge for stainless but easier for the copper or brass afcs. Even sanded down, the atty still gets pretty big air. But if that's what you're looking for, the Rogue should do it for you. Its easy to build on and the flavor is not bad either. Best of all, you can squonk on it all you want. It doesn't leak unless you hold it upside down. For me, its a pretty good atty overall.
What does sanding down the top cap achieve? Not sure I'm understanding how that increases control of airflow. I run my Odin at 0.3, given the small size of the chamber on the rogue, I'm hoping for A warmer vape. My buddy has a bf derringer, and it's crazy airflow and very warm, which is sometimes hard to achieve with reos because of the voltage drop. I ran a trident v2 on mine for 8 months and positively mastered the build on that thing. Odin is comparatively more difficult to build, rogue looks nice
Sanding basically allows you to reduce the airflow slightly. If you're after max air, I don't think sanding is needed. But for MTL guys, it helps, a little. Still airy though, even when the top cap is sanded down. I agree, it looks nice. Vapes good too.
MY Rogue will be here tomorrow. I'll have to convert it to BF but that's like a 15 minute job, so I should be able to report on it tomorrow evening...
Still not sure I'm understanding the point. Your trying to restrict the draw by sanding... What? Sorry lol, I'm just not getting it.
Anyways, I watched a couple reviews, including super x and he loved this thing, got one on the way real soon, thanks for find help all
Anyways, I watched a couple reviews, including super x and he loved this thing, got one on the way real soon, thanks for find help all
By sanding the bottom of the afc ring it allows the ring to sit lower letting you actually close off the holes otherwise it's still sitting high enough that air actually comes in from all around instead of those slots grooved into the top of afc ring
I recently picked up an authentic Rogue with the intention of having it modded for BF. But, unless the build I put in just sucks, I'm not that crazy about it from limited testing in conventional top feed mode. I like my Derringers a lot more than the Rogue so far. Guess I'll have to play with the build a bit when I have some time and see what I can get out of it. It may end up in the classies if I can't find a build I like for it.
Just built my first dual coil Rogue. Placed the 0.6 ohm net coils a little high. Checked on an ohm tester with the cap on to make sure they were not to high. They looked way high compared to builds on my other atomizers. I have to tell you, I am impressed! glad I bought two.
I just got mine from Chowderhead and built it for the first time today. I have to say it's totally awesome and airier than my Odin for sure. I didn't think it was quite as easy a build as for the Odin but once I got the hang of it it was easy peasy. It's going to be my go to atty.
Bottom fed? Better go look!There may or may not be an authentic Rogue in the classies.
I wanted the Rogue to work for me as a atty that won't leak like so many others do. But I have to agree... like sucking air through a vacuum hose, the AFC is worthless and the flavor is weak from it by my standards. I'm a long lung hitter, I don't like the Rogue at all and put in the out of service box still brand new.
Have to agree. I'm on my second setup of the rogue and flavor is OKAY. Not great. I'll keep playing though. Nice size and pretty much leak proof. Derringer has better flavor.
Going to try the omerta next....
Going to try the omerta next....
- Status
