Vaping Power Chart Adjusted

Status
Not open for further replies.

Nu2Dis

Super Member
ECF Veteran
Verified Member
May 24, 2013
902
1,296
Jersey Shore, NJ, USA
So, I'm always looking for ways to improve things, and enjoy helping other people; some may find this a complete waste of time, but I have compiled a new power chart. The one's I found were missing some small amounts of information.

For example. I have a 1.7 Ohm coil, and would like to vape at close to 6.5 Watts; the old chart skipped from 1.5 to 1.8 ohms and skipped from 3.2 - 3.4 Volts so you had to either guess, or get out the calculator to do the math (3.3Volts). I found myself doing this a lot and this spreadsheet just took a few minutes to put together. I hope it helps some one. I removed voltages over 6 and resistance over 4, as I have found little use myself.
 

Attachments

  • Vaping Power Chart My Own Rev.xlsx
    24.3 KB · Views: 339
Last edited:

retired1

Administrator
Admin
Supporting Member
ECF Veteran
Verified Member
Apr 5, 2013
51,272
45,927
Texas
A suggestion. As the old chart designates dangerous voltages as red, I'd suggest doing the same with your chart. The original has a wide range of viewership and folks tend to associate red with danger. Associating blue with the dangerous voltages is going to get a lot of folks into trouble if they're thinking of the original chart.
 

Nu2Dis

Super Member
ECF Veteran
Verified Member
May 24, 2013
902
1,296
Jersey Shore, NJ, USA
A suggestion. As the old chart designates dangerous voltages as red, I'd suggest doing the same with your chart. The original has a wide range of viewership and folks tend to associate red with danger. Associating blue with the dangerous voltages is going to get a lot of folks into trouble if they're thinking of the original chart.

I used Blue for low Voltage - low wattage - and Red for high Voltage - high Wattage. Did you see it differently?
 

retired1

Administrator
Admin
Supporting Member
ECF Veteran
Verified Member
Apr 5, 2013
51,272
45,927
Texas
I see absolutely no red at all in the pdf file.

4yGW1SZ.png
 

Nu2Dis

Super Member
ECF Veteran
Verified Member
May 24, 2013
902
1,296
Jersey Shore, NJ, USA
looking at this chart I'm vaping on a zmax v3 at 10w on a 2.0ohm evod that gives me a 4.45 volts I am on the red side but the taste is great i don't get a burnt taste and the flavor is much more pronounced than on say 8w
what does this imply?

This is just a guide. You may have juice that doesn't burn as easy, or just don't notice the burnt taste. I've seen fellow vapors push it up to about 12 Watts with success. If I personally go above 7.5 Watts, with any resistance coil, I notice a distinct burnt taste coming through. The one thing that doesn't show is the amp draw, but you should be well within the limits with your ZMAX
 

retired1

Administrator
Admin
Supporting Member
ECF Veteran
Verified Member
Apr 5, 2013
51,272
45,927
Texas
How does that happen????
How do I delete the link?

I restarted the machine and viewed it in Windows and the colors show as they should. However, a non-Windows machine may see the colors differently (I normally run in Linux). Ensure your PDF conversion isn't using colors that are strictly associated with Windows.
 

Ronald3638

Super Member
ECF Veteran
Aug 16, 2013
429
240
Zeeland, MI, USA
I don't understand I usually adjust the watts so 2ohm = 4 watts if I go higher the juice burns. doesn't matter if the coil is new or old. using vamo with a protank.

Make sure your not in average mode NO1 set your Vamo to RMS mode by holding either the Right or Left button until it displays the mode. If it displays NO2 when you do this it was in NO1 before you did this procedure.

Here's a spread sheet that illustrates the differences between average and RMS. If anyone finds an error feel free to fix it and repost.

View attachment Watts vs volts and resistance.xls
 
Status
Not open for further replies.

Users who are viewing this thread