VaporMoon & The Saber Touch Official Thread!

[Sweden]

Hello! I just ordered my first Saber Touch 5v. Do you have any vendor suggestions battery wise? I'm looking for 16340 3.7v 880mah batteries (as suggested), but am having trouble finding a trusted vendor who sells them.

Very much looking forward to my ST.

 

[Sir_Lawrence]

You can also use (2) 18350 3.7v batts. They are a little wider but last longer between charges.
Lighthound.com or batteryjuntion.com are very good places to look for batteries.

 

[Sir_Lawrence]

TGIF !
Too bad I have to work through the night!​

 

[Sir_Lawrence]

Just added a bunch of
Saber Touch Mods
To Our
Huge Savings Specials Page!

Check Them Out and

Keep On Vapin'!​

 

[Tat_skull]

Sup Moon Dwellers Just droppin' by to make sure alls ok on the Moon

 

[Sir_Lawrence]

Hey Tat!
Nice to see you hanging around a little!

 

[Sir_Lawrence]

Happy Easter!

Keep On Vapin'!​

 

[Kropotkin]

Hello! I just ordered my first Saber Touch 5v. Do you have any vendor suggestions battery wise? I'm looking for 16340 3.7v 880mah batteries (as suggested), but am having trouble finding a trusted vendor who sells them.

Very much looking forward to my ST.

Hello.

I just bought several AW batteries from Fluid Vapor, and both prices and shipping time were pretty awesome:

Batteries



Hi Tat_Skull!

 

[Sir_Lawrence]

Hello.

I just bought several AW batteries from Fluid Vapor, and both prices and shipping time were pretty awesome:

Batteries



Hi Tat_Skull!

That is a good price. Thanks for showing us!

 

[Tat_skull]

Hey Tat!
Nice to see you hanging around a little!

Hey Sir Lawrence! Hope all is well

Hello.

I just bought several AW batteries from Fluid Vapor, and both prices and shipping time were pretty awesome:

Batteries



Hi Tat_Skull!

Hey Kropotkin, Nice to see your here on the Moon.

A couple other Places to find some good Prices on AW's would be Super T Manufacturing and RTD Vapor, give em a look

 

[Riggsy]

Quick question for all you saber owners... I just purchased an AGA-T2 (LOVE IT!! MY GOD THE FLAVOR!!! I CAN TASTE MY JUICE AND NOT SILICA!!!) Anyways it sits SO flush agenst the saber that i was worried about it even firing. There is literally not even a mm of gap. I will be ordering more sabers in the future and just wish to make sure no one has had any issues with these RBA's.


On a funny side note, built my first coil on the AGA.. was a 4/4 wrap of 28 gauge Kanthal reading at 1.0 ohms on the dot. Tried using it with the kick... was like ... this is 1 ohm at 9 watts this should be BURT BURNT BURT!!! so i crank it to 10 watts... same result.. Meh vape. Pull the kick out, put in the replacement kick.. same result. Pull the kick out, use the battery extension and vape off the battery alone... INCREDIBLE VAPE! lol did some reading and the kick wont work below 1.3 ohms. was just tryin to get the lowest res possible to make batteries last as long as possible .

 

[Sir_Lawrence]

Shouldn't worry. Remember, it's only the center pin of any atty or the Saber's connector that is positive. Now, remember not to over tighten anything. You don't want to initiate problems by pushing that center pin down to far.

 

[Riggsy]

"Your a quick one!" - Billy Madison Thanks for the fast response! Very true. I guess my main concern is that a single millimeter would mean the center post wouldn't make contact.

 

[Sir_Lawrence]

You should be fine!
You can also pull down the center connector on that atty to make better contact.

 

[Tat_skull]

Quick question for all you saber owners... I just purchased an AGA-T2 (LOVE IT!! MY GOD THE FLAVOR!!! I CAN TASTE MY JUICE AND NOT SILICA!!!) Anyways it sits SO flush agenst the saber that i was worried about it even firing. There is literally not even a mm of gap. I will be ordering more sabers in the future and just wish to make sure no one has had any issues with these RBA's.


On a funny side note, built my first coil on the AGA.. was a 4/4 wrap of 28 gauge Kanthal reading at 1.0 ohms on the dot. Tried using it with the kick... was like ... this is 1 ohm at 9 watts this should be BURT BURNT BURT!!! so i crank it to 10 watts... same result.. Meh vape. Pull the kick out, put in the replacement kick.. same result. Pull the kick out, use the battery extension and vape off the battery alone... INCREDIBLE VAPE! lol did some reading and the kick wont work below 1.3 ohms. was just tryin to get the lowest res possible to make batteries last as long as possible .

Welcome to the wonderful world of Genesis atty's Riggsy The kick is a no go with geny's. It's incredible the flavor you get from a 1.0 ohm coil with a 3.7 batt, and to think with that , you are vaping way above the 10 watts that a kick goes up to. Now as far as worrying that it wont fire, thats the thing, most geny's have an adjustable center pin which will allow it to work on anything And now if I'm reading this correct, you were trying to get the lowest res possible to make batts last longer? Its actually the opposite, the lower the res, the quicker your gonna be changing batts, but hey it's worth it

 

[Kropotkin]

Quick question for all you saber owners... I just purchased an AGA-T2 (LOVE IT!! MY GOD THE FLAVOR!!! I CAN TASTE MY JUICE AND NOT SILICA!!!) Anyways it sits SO flush agenst the saber that i was worried about it even firing. There is literally not even a mm of gap. I will be ordering more sabers in the future and just wish to make sure no one has had any issues with these RBA's.

I use AGAs and IGOs on all the Sabers, and they're perfect. They look great and vape just beautifully.

The only thing I've ever had trouble with, in 8 months as a major Saber geek, is a cheapie little Phoenix clone - but that thing is a weirdo anyway, and won't fire on anything except the Telescope I bought for rebuilding.

 

[Sir_Lawrence]

TGIF

Let's Make Some Noise!​

 

[Sir_Lawrence]

Starting to feel like Summer on the east coast!
To be around 80+F today!

 

[Nitrobex]

A few silly questions...
I like vaping small devices, 18350, will it fit in a mini or do I have to go with a midi with the thingy inside it?
Can I get the 6 line with the textured grip like on the saber maxx on a mini/midi?
Which cap looks the best (flush) with the AGA-T?
Will the mini/midi handle high amp drain?

Thanks in advance Sir_Lawrence =)

 

[Sir_Lawrence]

A few silly questions...
I like vaping small devices, 18350, will it fit in a mini or do I have to go with a midi with the thingy inside it?
Can I get the 6 line with the textured grip like on the saber maxx on a mini/midi?
Which cap looks the best (flush) with the AGA-T?
Will the mini/midi handle high amp drain?

Thanks in advance Sir_Lawrence =)

You Can use the 18350 with the Mini...
Yes, you can get the 6 lines with the textured grip...
Not sure about the AGA-T...
Yes, the Mini can handle anything up to 24 Amps!

Hope this helps!