Anyone like the vision as much as I do. I have heard a lot of people say it leaks but I have not seen that. I have only put 20 drops in it at a time and no leaks. Lot of vapor and throat hit. Any comments?
Vision Eternity
- Thread starter Railrust
- Start date
- th_trl_thread_readers 0
- Status
I envy you lol, there seems to be about a 50/50 split on the quality. mine leaks and gurgles like crazy and the only explanation I can think of is the air feed tube is too short or something is not set correctly. mouthfuls of juice. or running down the sides of my battery constantly, or no wicking.
the little it worked in between all that was massive amounts of vapor. when it works it works extremely well, and thought it was cool how the wicks come w extra pushpins, now it sits in the not used bin while i wait for a dripper pro.
sad as its extremely nice to look at too.
glad you got lucky and enjoy it!!
the little it worked in between all that was massive amounts of vapor. when it works it works extremely well, and thought it was cool how the wicks come w extra pushpins, now it sits in the not used bin while i wait for a dripper pro.
sad as its extremely nice to look at too.
glad you got lucky and enjoy it!!
I picked one up the other day. If overfilled, I get gurgles, if severely overfilled, I get leaks.
Other than that, it works great!
Other than that, it works great!
I was impressed with the build quality and performance of the Eternity, the vape was cooler than I usually prefer but I did REALLY like the draw, and the flavor and vapor production were quite good.
The DESIGN is absolute garbage though. The insulated post that you push the little coil blocks onto is weak, and WILL break eventually depending on how lucky you get. It doesn't snap or anything (although I guess that's possible) but it's too weak to put up with the large amount of force needed to seat those little blocks.
3 coils is what I was able to go through before the post got wobbly and started shorting out. I could check my atty rez on my mod and it would change from 2.5, to 2.2, 2.1. 1.8. 1.5 and keep going down as the the post moved around, shorting out the device.
This tiny, single flaw is a huge deal breaker for me. This 30 atty is completely useless now. There is no way to "get into" the area underneath the coil to fix the wobbly post.
On one of those China sites I've seen an Eternity knockoff that uses small screws INSIDE of the post, with a horizontal hole lower down. You don't need to remove the screws, just loosen then a bit, insert your wire, and tighten it down. Much easier setup than the Vision, and you don't need to put ridiculous amounts of force on that tiny little pin.
But when copying the ET they forgot to include that little air tube that sticks up right underneath the coil. I'd imagine this woud cause severe leaking, as that tube is where the airflow comes from, being raised up it's much more difficult for juice to leak through it, but if it's flush with the bottom like on the knock-off juice could easily leak out.
So the china copycats got one thing right, the posts for the coil, but they screwed up somewhere else.
Vision got it right on the air tube, but screwed up big time on the posts.
If these posts were fixed I'd buy another ET even after swearing off Vision products (every single one I've had, Vivi Nova, other clearo, twist, ET) were all complete trash and either broke or failed to perform. But better pins would convince me to get another ET.
The DESIGN is absolute garbage though. The insulated post that you push the little coil blocks onto is weak, and WILL break eventually depending on how lucky you get. It doesn't snap or anything (although I guess that's possible) but it's too weak to put up with the large amount of force needed to seat those little blocks.
3 coils is what I was able to go through before the post got wobbly and started shorting out. I could check my atty rez on my mod and it would change from 2.5, to 2.2, 2.1. 1.8. 1.5 and keep going down as the the post moved around, shorting out the device.
This tiny, single flaw is a huge deal breaker for me. This 30 atty is completely useless now. There is no way to "get into" the area underneath the coil to fix the wobbly post.
On one of those China sites I've seen an Eternity knockoff that uses small screws INSIDE of the post, with a horizontal hole lower down. You don't need to remove the screws, just loosen then a bit, insert your wire, and tighten it down. Much easier setup than the Vision, and you don't need to put ridiculous amounts of force on that tiny little pin.
But when copying the ET they forgot to include that little air tube that sticks up right underneath the coil. I'd imagine this woud cause severe leaking, as that tube is where the airflow comes from, being raised up it's much more difficult for juice to leak through it, but if it's flush with the bottom like on the knock-off juice could easily leak out.
So the china copycats got one thing right, the posts for the coil, but they screwed up somewhere else.
Vision got it right on the air tube, but screwed up big time on the posts.
If these posts were fixed I'd buy another ET even after swearing off Vision products (every single one I've had, Vivi Nova, other clearo, twist, ET) were all complete trash and either broke or failed to perform. But better pins would convince me to get another ET.
Hadn't given any love to the Eternity in quite some time, dripped in 30 drops in with my loose positive post and vaped away, no leaks no gurgles. Did you folks see the demo where the poster showed how when dripping into it it would drip off the coil and right down the air tube?
I noticed today that the threads on the body are the same as an A-7 but the ID of the Eternity tube is smaller and doesn't clear the heads of the screws on the A-7's posts, if the Eternity was Stainless steel I'd make that work but oh well.
Never mind, it eventually leaked
I noticed today that the threads on the body are the same as an A-7 but the ID of the Eternity tube is smaller and doesn't clear the heads of the screws on the A-7's posts, if the Eternity was Stainless steel I'd make that work but oh well.
Never mind, it eventually leaked
Last edited:
I have one that has been working perfect for over 2 months. I also have an AGA Tiamat that for the life of me get working. On my Vision, I every once in a while get a gurgling sound. If it doesn't go away I just take it off and blow thru it and problem solved. This one I have rebuilt with 0 problems.
I too am having trouble with the push on posts. When I push them on too far they tend to cut the coil wire off and the coil then comes off. If I only push them snug without seating the all the way, it works great. I do think it is a fantastic looking unit. I would buy another if they re-engineer it in a later release with screws instead of pins.
Schlim66
Schlim66
So far so good with mine. Definitely does not hold 40 drops without leaking. Just put 10 in or so. Beats a 510. Waiting on an A7. Should be here tomorrow...
I don't know how safe it is but I added a little super glue gel to the base of my loose, leaking positive post.
After it dried I put a new wick and coil on it, so far so good
After it dried I put a new wick and coil on it, so far so good
- Status
Similar threads
- Locked
- Poll
