Vulcan for 12.99

[rizzo777]

Anyone have this rba? http://www.justvaping.net/index.php?main_page=product_info&cPath=4&products_id=1

I ordered one and just found out its not completely SS...ugh...I wanted a smaller rba as my aga-t+ is huge

 

[Rule62]

I've had a couple of those. They set up well. Smaller than the AGA-T

 

[donnah]

I've got one. the wick hole is very small and I get really bad runback (dark juice). The top cap stops turning opposite the air hole and it has to be unscrewed half way, which makes it loose and very unstable. I never could get mine to perform consistently.

 

[ricks]

I've got 2 of them and they work great

 

[rizzo777]

I tried to cancel the order but it shipped already, I will keep it due to the price and fast shipping hopefully I can get it to work

 

[Plumes.91]

you can get it to work, but you might want to drill out the hole or drill a new one by the wick hole.
It'll work man. until you can drill you might like unscrewing the cap till the air holes by the wick.

 

[rizzo777]

What size did you drill out the hole with?

 

[Rule62]

If the air hole doesn't line up with the wick, you can sand the bottom of the cap. Sand a little, and just keep trying it. Eventially, you'll get it to line up.

 

[KalThaxx]

The oring on mine is big enough that it doesn't leak with it turned back a half a turn. It's been going strong for over two months.

 

[MJBinNM]

This one is *mostly* SS The Vulcan - Rebuildable Atomizer Tank (Satin) The inside tube and positive post seem to be plated brass, but the cap, top plate and bottom plate are all SS. The machining is much better than the chrome plated ones.

I got a couple of the chrome ones a few months ago and they've worked great. It's not that hard to get the air hole to line up either. I've since bought a couple of the SS ones, I got mine from Cloud 9 in the UK which cost a bit more but worth it to me (Couldn't find any state-side at the time). I also got a couple Pyrex tanks from IBTanked. They look great on my P+18350 slant top!

 

[rizzo777]

Thats the one I wanted but was sold out yesterday. Hopefully the one I ordered from the op is the same

 

[MJBinNM]

Thats the one I wanted but was sold out yesterday. Hopefully the one I ordered from the op is the same

I just got a notification email from Sure Vapes this morning that it was back in stock...maybe you'll get lucky and the one you ordered will be the SS one...can't really tell from the picture on their site since it's in the packaging...

 

[rizzo777]

Vaping good so far, got the airhole to lineup. Airhole is very tiny though, any recommended size to drill it out some?

 

[ricks]

Give it some more vaping time. you might get to like this way.

 

[rizzo777]

Anyone ever have a problem filling this tank with a needle top bottle? When filling juice comes out of the wick and negative battery terminal when the needle is on the opposite side...might sound stupid but its fustrating

 

[ricks]

I had that problem too. I use a syringe that has a 1 1/2" long needle and you just have to fill it with the tip of the needle in the liquid. Someone on here told me this fix.

Anyone ever have a problem filling this tank with a needle top bottle? When filling juice comes out of the wick and negative battery terminal when the needle is on the opposite side...might sound stupid but its fustrating

 

[MJBinNM]

Vaping good so far, got the airhole to lineup. Airhole is very tiny though, any recommended size to drill it out some?

Dremel makes a set of small drill bits that you can get for about 6 bucks. I used the 3/64" bit to drill mine out. That's about 1.2 mm. If that's not big enough, you can always go up to 1/16" which is just over 1.5 mm, but that would probably be too big.

 

[Cool_Breeze]

Anyone ever have a problem filling this tank with a needle top bottle? When filling juice comes out of the wick and negative battery terminal when the needle is on the opposite side...might sound stupid but its fustrating

I sometimes unscrew the negative screw. Also, if my wick is small, it's not so much a problem.

 

[beanpusher]

i drill all my air holes to 1/16th for alot of people its a bit airy but running sub ohm coils all you need are short quick drags to get a huge cloud. these attys are fairly cheap to play with. but always try your product out for a day or two to make sure that you want to modify it. sometimes we have to change the way we vape to different attys.