We want Small Rba guys!

[rzil]

I don't get why almost every rba is so large , why not make some small .

I just got my Mini kayfun clone and even though it doesn't weight a ton like my 3.1 clone , it is still really long so I can walk around with it only with a 650 .
I don't get why vendors are not making an effort to create something small for out and about , after all... I'm not going to take my Magneto + 3.1 kayfun clone outside

 

[Blackboar]

Pick up a nano kit for your 3.1. That is about as small a RTA as you can get. Otherwise, to get a shorter profile, you'll have to go to a dripper.

 

[vapdivrr]

Check out the erlkonigin or erlprinz, with both you have the option of a nano kit that holds 3mls. In nano mode this atty is really small and the lightest out there. As for much smaller RTA tanks, they do even make them smaller, I believe 14, maybe 18mm, along with those I have seen matching mods that push them.

 

[CMD-Ky]

I agree. I have the Taifun and found a nano kit on Fasttech making it about half the size and weight. I get more liquid into the tank by stripping a Q-Tip and inserting it into the air tube plugging it and fill it almost, not quite, to the tank threads. This works great, best of both worlds

I don't get why almost every RBA is so large , why not make some small .

I just got my Mini Kayfun clone and even though it doesn't weight a ton like my 3.1 clone , it is still really long so I can walk around with it only with a 650 .
I don't get why vendors are not making an effort to create something small for out and about , after all... I'm not going to take my Magneto + 3.1 kayfun clone outside

 

[vapdivrr]

Although they do make mini RTA tanks, I think the main reason you don't see more of them is because under 21mm, the decks become a little harder to work on. Because of this, there is not a big call for them so companies don't make them like regular sized attys. I think for those who want smaller sized devices then go to pre made devices like the ego/protank mini combo but for rebuildables in that size, there are some but not wide spread.

 

[themyst]

Although my DNA30 clone / Orchid combo is deadly; for daily use to and from work, I use an MVP2 or e-Go VW mod with a Kanger dual-coil Aerotank. The DNA30 RBA setup is a brick compared to an eGo on an Aerotank mini.

 

[MrPlink]

Learn to build protanks?
:shrug:

 

[Marc411]

Learn to build protanks?
:shrug:

+1

I have the PT2 and put AFC on all of them and they produce a nice vape when I need to go small. Those and the IStick are a stealth vape and damn tasty.

 

[keepsmiling]

Just built my KF mini clone in black. It was very difficult to capture the wire on those tiny screws, but I finally got it{old eyes can't see}
I need a magnifying something or other..
Firing it on my black istick. I only used the short version. I like it.

 

[roxynoodle]

Focalecig has a nice stumpy kit for the Rose now. Lemo Drop should be out soon.

 

[SkvLTD]

Or just take KF with you and vape like a boss. After all, its not a 30mm mod for 26xxx batteries....

 

[roxynoodle]

How about the Ruzgar?

 

[Btsmokincat]

Mini fogger due out in the next few weeks. Pauly Meatballs did a video breakdown on YouTube. Looks awesome!

 

[WattWick]

The Sat 22 is small-ish without sacrificing too much capacity.

 

[Firestorm]

I'm not sure what the OP considers to be a large RBA but I prefer 22mm atomizers to fit on my 22mm mods. If we're talking height then I agree since I prefer mechanical mods in 18350 mode and I really don't want an atomizer that is taller than my mod. I have been using a Spheroid lately which is a 16mm atomizer, but otherwise I like my mods and atomizers to have the same diameter.

 

[keepsmiling]

The Taifun gs is also small.

 

[BobC]

You want stealth? Leave tanks behind,
Go with a tiny mechanical bottom feeder, with a small footprint BF dripper (i.e. Cyclone, Divo, PDA for single coil and Reactor, Nuppin for dual)


You get 6 ml juice in the mech (or DNA type) body, and a smaller footprint then a Spinner 1200