What fluxomizer ohm to get for kgo

[evosil98]

Hey, I'm really interested in getting a clearomizer but can't decide what to get. I'm really leaning towards the fluxomizer.

Thinking about getting the Fluxomizer deluxe from gotvapes and they have 4 different ohm levels.
2.4-2.6 ohm
2.6-2.8 ohm
2.8-3.0 ohm
3.0-3.2 ohm

I keep hearing to get low ohm for warm hits like the 1.7ohm resurrections but why is all the fluxs 2.4ohm and above?

what would I need to have great hits from a Kgo? Thanks

 

[burns_erin]

What volts does a kgo run. To me, a 2.8 cart in a 3.2 volt device runs pretty cool, but thats my preference. I would imagine though lower resistance would likely result in scorched wicks and popped coils. But I am not exactly an expert.

If you like a warmer vape I would suggest trying the lowest available resistance.

Sent from my G2...so please excuse the spelling errors, correct gets the best of me.

 

[evosil98]

The Kgo run 3.7v batteries. I leaning toward the 2.4-2.6 ohm but a few suggested the 2.6-2.8. any more input would be appreciated

 

[burns_erin]

The Kgo run 3.7v batteries. I leaning toward the 2.4-2.6 ohm but a few suggested the 2.6-2.8. any more input would be appreciated

Well, on my vv 3.7 isn't that warm, if you want warm then the 2.4-2.6 sounds about right. And it should still be in the safe range based on ohms law.

Sent from my G2...so please excuse the spelling errors, correct gets the best of me.

 

[Adrena]

burns you're awesome, Just thought I'd agree with you again 5*

 

[burns_erin]

burns you're awesome, Just thought I'd agree with you again 5*

Well Thanks

 

[zer0ith]

I'll put in my

Some juices at 3.7v with a 2.4-2.6 will be amazing..... other ones will be giving a burnt type taste. IMHO its all about the juice & device.
If funds allow you get a box of both and test it out, see which ones give you what your looking for. For all you know you may not like them.
Personally they are amazing! German Chocolate cake i use w/2.6-2.8 ohm ce2 on my 3.7v box mod is sooooo good. Its not to warm, but warm enough and because its a sweet juice it doesn't give me that burnt taste. Try it with the 2.4-2.6 and you get a different taste (not as good).

 

[evosil98]

Thanks everyone for your comments.

I read somewhere in the forums that since the flux atty is closer to the mouth it will give a warmer vape at higher ohm's than a lower ohm with the standard atty set up.

Im really hoping that these clearomizer vape the way I want 2. I don't really want to use cartomizer cause of the thought of the burning polyfillers.

 

[eso]

2.4-2.6 Fluxo runs best on my KGo

 

[Stef64]

On my Riva, the 2.4-2.6 Fluxos give a nice warm vape. 2.6-2.8 are a bit cool for me but still vape OK.

 

[zoiDman]

Thanks everyone for your comments.

I read somewhere in the forums that since the flux atty is closer to the mouth it will give a warmer vape at higher ohm's than a lower ohm with the standard atty set up.

Im really hoping that these clearomizer vape the way I want 2. I don't really want to use cartomizer cause of the thought of the burning polyfillers.

A CE2 does give a Warmer hit since the Atomizer Coil is close to your lips. Couple that with 2.4~2.6ohm and you get a Nice warm hit.

I perfer the 2.6~2.8ohm CE2's. And I recommend them to people who have never used a CE2 before because they tend to more forgiving when it comes to wicking.

BTW - A shame there is a ohm sampler 6-Pack that had 2 cartos of the lower 3 ohm ranges.

BTW2 - You might want to skim thru this thread while your waiting for your CE2's to arrive. Lots of good Info and Tips.
http://www.e-cigarette-forum.com/fo...s-tricks-ce-2-mods-technical-info-videos.html

BTW3 - Did you notice how much More help you get with CE2's here in gotvapes corner of the ECF?

 

[MsTick]

I use the 2.6 - 2.8 on my Rivas. I vape high VG juices, and the lower ohms give me burnt hits. The vape is warm, not hot, so I like them at this range. And listen to zoid and do the seal mod.

 

[evosil98]

Thanks guys for the input. On brand new Clearomizers do I have to do a dry burn or clean them before using?

Does it have a primer?

Thanks

 

[zoiDman]

Thanks guys for the input. On brand new Clearomizers do I have to do a dry burn or clean them before using?

Does it have a primer?

Thanks

Even though the New CE2's that come from gotvapes Rarely have anything on the wicks, it is a Very good idea to give the CE2 a quick 2~3 second pulse of power to check for any smoke.

If you don’t get any smoke, your Good to Go and can Fill.

If you do get a Twinge of Smoke, Give it another 2~3 second pulse until there is no smoke. Then you can fill.

I Rinse and Dry ALL new CE2’s that I use in Hot Water but some call that Overkill.

 

[mycro]

just received my kgo the other day and had also ordered fluxomizer xl 2.6-2.8 to try. I really like these and they are working great with the kgo.

 

[badkolo]

glad your liking them, merry christmas