What's in your kit?
- Thread starter mrtinee
- Start date
- th_trl_thread_readers 0
- Status
Small set of nippers
tweezers
Various mandrel sizes
small precision screwdriver set
Multimeter
set of jewlers pliers
torch
building base
tweezers
Various mandrel sizes
small precision screwdriver set
Multimeter
set of jewlers pliers
torch
building base
Last edited:
precision screwdriver set
~ 10 meters of kanthal wrapped around a small spindle (when it gets low, I just clip another 10m off my big spindle and wind it onto the small one - it's more portable that way)
Cotton
nail clippers
offset tweezers
A quilting pin (the knob on the top makes it easier to hold onto while coaxing the coils into a better position)
two of the blue screwdrivers that come with rebuildable atomizers - one philips, one flathead
A few sheets of "vaper towel"
One of those cheap rubber atomizer stands
An extra MVP charging cord
A 15 ml bottle of juice, in case I forget to grab some or run out
Two extra blunt tip needle caps
It all fits in one of those little Ego cases I had lying around with room to spare. My MVP2s have ohm meters built in, so I don't generally carry my dedicated ohm meter around.
~ 10 meters of kanthal wrapped around a small spindle (when it gets low, I just clip another 10m off my big spindle and wind it onto the small one - it's more portable that way)
Cotton
nail clippers
offset tweezers
A quilting pin (the knob on the top makes it easier to hold onto while coaxing the coils into a better position)
two of the blue screwdrivers that come with rebuildable atomizers - one philips, one flathead
A few sheets of "vaper towel"
One of those cheap rubber atomizer stands
An extra MVP charging cord
A 15 ml bottle of juice, in case I forget to grab some or run out
Two extra blunt tip needle caps
It all fits in one of those little Ego cases I had lying around with room to spare. My MVP2s have ohm meters built in, so I don't generally carry my dedicated ohm meter around.
Dozens of bottles of juice
a ton of screwdrivers that came with atty's
2x 5/64" drill bits
Spare parts for attys
drip tips
crappy kanthal that came with atty's
mod parts
nicoticket business card
springs for nemesis and Pegasus mods
extra mod parts
that's just whats in my box... spread out on my desk is....
itaste VTR
ohm meter with a magma clone on it
30 gauge kanthal holding my kayfun 3.1 clone
28 gauge kanthal holding my Russian 91% clone
26 gauge kanthal holding my tobh atty clone
mixed nemesis with stillare
brass stingray clone
Pegasus clone with zenith v2
7 bottles of juice
1x sony vtc 4
efest battery pack with 3x sony vtc 5
xikar butane torch lighter
crown clone
nail clippers
tweezers
kanger beauty ring
carbona silver polish wipes
couple more screwdrivers
7 replacement tanks for my kayfuns
and an alan wrench for my zenith
a ton of screwdrivers that came with atty's
2x 5/64" drill bits
Spare parts for attys
drip tips
crappy kanthal that came with atty's
mod parts
nicoticket business card
springs for nemesis and Pegasus mods
extra mod parts
that's just whats in my box... spread out on my desk is....
itaste VTR
ohm meter with a magma clone on it
30 gauge kanthal holding my kayfun 3.1 clone
28 gauge kanthal holding my Russian 91% clone
26 gauge kanthal holding my tobh atty clone
mixed nemesis with stillare
brass stingray clone
Pegasus clone with zenith v2
7 bottles of juice
1x sony vtc 4
efest battery pack with 3x sony vtc 5
xikar butane torch lighter
crown clone
nail clippers
tweezers
kanger beauty ring
carbona silver polish wipes
couple more screwdrivers
7 replacement tanks for my kayfuns
and an alan wrench for my zenith
A lot of what I have is covered in this thread: What tools you use for wrapping coils (coil jig, or metal rods, or etc.)
aerin's already covered "vaper towel" = paper towel (meant to clarify that in my original post, sorry).
These are atomizer stands:
It's so that your atomizer can sit stable on a flat surface without having to lie it on its side - handy for rebuilding or for swapping tanks/atomizers. Anything with Ego threading doesn't need a stand to sit flat when it's upright, but things that are 510 threaded (protruding pin on the bottom) do.
I have a few aluminum stands for rebuilding at home, but the rubber ones are more handy for out and about because they don't get dented or scratch surfaces the way the aluminum ones can.
Thanks! I thought those were like a beauty ring awesome anyone have a link to rubber ones?
The rubber ones are often sold as "Ego stands" because they'll also fit Egos, but they work the same as the aluminum ones for rebuilding (or for being able to store your tanks/atomizers upright). I got mine free from my local B&M, but here's a link to some online. I've never used the vendor in that link, so I can't vouch for their reliability.
My vape box has size 28 gauge Kanthal and sizes 30,32,26, and ribbon wire. I have two sizes of ekowool, organic unbleached cotton, 100% sterile cotton, scissors, wire cutters, tweezers, small and large hemostat, butane torch, a roll of stainless steel mesh wicking material, silica wicking material, syringe needles, various sizes of screw drivers, efest batteries, o rings and washers, alagator clips, magnification glass, magnet, pliers various sizes, two digital ohm testers, replacement tank parts, needles and 0.5*0.1 kanthal flat ribbon wire. I have a build station set up in my kitchen and these things are in a kit container on my building station. Hubby does not mind because I build for him as well. 
As of right now all I have is an ego starter kit and 4. 6 MLK bottles of juice plan on adding much more starting with a portable and then hopefully a 3 d atomized and either a nemesis or stingrays mod
Fun thread.
I have a "tactical bag" that I got from amazon. Green canvas. In hindsight getting something that looks like it holds a gun was silly. Can't leave it in my car.
Inside of that --
Tool Container:
1 set of jewelers screwdrivers
1 pair needle tweezers
1 pair ss surgical scissors
1 pair wire snips
2 pair jewelers round nose pliers
1 pair jewelers flat nosed pliers
Build container:
1 spool 28 GA kanthal
1 spool 30 GA kanthal
2 AA batteries
1 510 threaded Ohm Meter
1 Coil Jig
Random Container:
5 feet rayon
2 blunt tip syringes
Various o-rings and other nonsense
Loose:
1 can of butane
1 Torch
Nitecore I4
I have a "tactical bag" that I got from amazon. Green canvas. In hindsight getting something that looks like it holds a gun was silly. Can't leave it in my car.
Inside of that --
Tool Container:
1 set of jewelers screwdrivers
1 pair needle tweezers
1 pair ss surgical scissors
1 pair wire snips
2 pair jewelers round nose pliers
1 pair jewelers flat nosed pliers
Build container:
1 spool 28 GA kanthal
1 spool 30 GA kanthal
2 AA batteries
1 510 threaded Ohm Meter
1 Coil Jig
Random Container:
5 feet rayon
2 blunt tip syringes
Various o-rings and other nonsense
Loose:
1 can of butane
1 Torch
Nitecore I4
Yep, should have got a sponge bob squarepants backpack!
I'm more of a pokemon guy, but I like your thinking hehehe!
Another thing I have found invaluable is these lil "coin" bags... they work for everything... wet coils, cotton balls, o rings, just about anything... I keep a few in my kit just in case...
**keep calm and vape on**
Sent from my Note 3 via Tapatalk
Last edited:
Another thing I have found invaluable is these lil "coin" bags... they work for everything... wet coils, cotton balls, o rings, just about anything... I keep a few in my kit just in case...
**keep calm and vape on**
Sent from my Note 3 via Tapatalk
I use to work for Wal-Mart and I ...... off a manager by calling them "dime bags" to a customer. heh.
Anyways, my kit includes
Coil Jig
Pliers
Ohm Reader
Cotton Balls
Wire
Screw Driver
what ever juice I decide to carry that day
- Status
Similar threads
