Last night I received my vaporDNA order:
1 - Doge X by Congrevape
1 - Mutation X V3 by Indulgence
1 - EHPro Pontus V1.5 Dripping tank Atomizer
I was so excited!! When I ripped open the box I was stunned! The EHPro was sitting right on top in this elegant black box! Quite an impressive sight!!
The Mutation X V3 looks killer too! Nice box, slick looking in the see through window! Was a little disappointed that the Drip Tip that comes with it is PLASTIC. That was a bit disappointing. But this thing looks amazing!
The Doge X - I don't even have words for this thing!! Intimidating comes to mind! The chuff tip (which is NOT removable) on this guy is MASSIVE!!!! MASSIVE (yes I said it again!)!! It almost seems too much!! But very excited to build some coils for this guy and start blowing some clouds!!
It was late last night when I finally got to sit down with them. The only one I was able to clean and get put together was the EHPro Pontus V1.5. Taking it apart was a pain in the, well, in the you know what!! The pyrex glass wouldn't come off the bottom part and every time I would twist and/or pull on it, it felt like the glass was going to Shatter (but it didn't, eventually it popped off). Unfortunately, this dripping tank does NOT come with instructions. So dis-assembly was a little time consuming, trying to figure out which portion to remove and which screws to loose. But thank you YouTube for 1 helpful video.
Anyway, built some 1.6ohm coils out of 28ga Kanthal, was shooting for 0.8ohm final resistance at my atty. Let me tell you, the screws on this thing Do NOT want to HOLD down wire. One constantly backs out and the other just Breaks the Kanthal. And I am not even screwing them down that Hard or "forceful". So after getting the wires in and screws down and wicked, I fired it up but the Atty reads 0.9ohm then JUMPS up to 1.4ohm, then down to 1.0ohm then up to 1.2ohm, then down to 0.9 then up. It won't hold steady! So I took off the top and screwed down that screw that keeps coming out, was fine for a pull or two, then started bouncing around again.
I contacted vaporDNA who I made the purchase from via email (no one seems to answer their customer service phone number) and I also contacted EHPro about it. So we'll see what happens.
VaporDNA, so far is pretty good. Shipped the items on the 12th and I got them on the 16th. So pretty fast shipping (it was FREE!). They even send a FREE bottle of juice along with any purchase! Its 60/40 (VG/PG) and they wrote that that is the Only ratio they'll send for the free juice! Which is fine by me, I don't tend to look "Gift Horses in the Mouth".
Any way, I would post pics but can't while I'm at work! Just wanted to update everybody!!
More updates to come as well, once I get my Doge X and Mutation V3 coiled and wicked!!!
1 - Doge X by Congrevape
1 - Mutation X V3 by Indulgence
1 - EHPro Pontus V1.5 Dripping tank Atomizer
I was so excited!! When I ripped open the box I was stunned! The EHPro was sitting right on top in this elegant black box! Quite an impressive sight!!
The Mutation X V3 looks killer too! Nice box, slick looking in the see through window! Was a little disappointed that the Drip Tip that comes with it is PLASTIC. That was a bit disappointing. But this thing looks amazing!
The Doge X - I don't even have words for this thing!! Intimidating comes to mind! The chuff tip (which is NOT removable) on this guy is MASSIVE!!!! MASSIVE (yes I said it again!)!! It almost seems too much!! But very excited to build some coils for this guy and start blowing some clouds!!
It was late last night when I finally got to sit down with them. The only one I was able to clean and get put together was the EHPro Pontus V1.5. Taking it apart was a pain in the, well, in the you know what!! The pyrex glass wouldn't come off the bottom part and every time I would twist and/or pull on it, it felt like the glass was going to Shatter (but it didn't, eventually it popped off). Unfortunately, this dripping tank does NOT come with instructions. So dis-assembly was a little time consuming, trying to figure out which portion to remove and which screws to loose. But thank you YouTube for 1 helpful video.
Anyway, built some 1.6ohm coils out of 28ga Kanthal, was shooting for 0.8ohm final resistance at my atty. Let me tell you, the screws on this thing Do NOT want to HOLD down wire. One constantly backs out and the other just Breaks the Kanthal. And I am not even screwing them down that Hard or "forceful". So after getting the wires in and screws down and wicked, I fired it up but the Atty reads 0.9ohm then JUMPS up to 1.4ohm, then down to 1.0ohm then up to 1.2ohm, then down to 0.9 then up. It won't hold steady! So I took off the top and screwed down that screw that keeps coming out, was fine for a pull or two, then started bouncing around again.
I contacted vaporDNA who I made the purchase from via email (no one seems to answer their customer service phone number) and I also contacted EHPro about it. So we'll see what happens.
VaporDNA, so far is pretty good. Shipped the items on the 12th and I got them on the 16th. So pretty fast shipping (it was FREE!). They even send a FREE bottle of juice along with any purchase! Its 60/40 (VG/PG) and they wrote that that is the Only ratio they'll send for the free juice! Which is fine by me, I don't tend to look "Gift Horses in the Mouth".
Any way, I would post pics but can't while I'm at work! Just wanted to update everybody!!
More updates to come as well, once I get my Doge X and Mutation V3 coiled and wicked!!!
Last edited:
