Wotofo Comp Wire (or other pre-built wire) on Kanger Subtank Mini RBA
- Thread starter Redo
- Start date
- th_trl_thread_readers 0
- Status
Anyone know if Wotofo Comp Wire (pre-built 'fancy' wires) would fit on the Kanger Subtank (or Toptank) mini rba's?
Subtank Mini coil inner diameter is approximately 2mm, but 2.5mm works fine.
They should all fit, but those highlighted in red are slightly closer to the original
2mm inner diameter spec.
Coil Specifications:
Twisted Wire: 26AWG, ~2.2mm Inner Diamater, 0.5Ω - 0.6Ω
Quad Twisted Wire: 26AWG, ~2.2mm Inner Diamater, 0.25Ω - 0.35Ω
Tiger Wire: 26AWG and 0.8mm x 0.2mm Flat Wire, ~2.2mm Inner Diamater, 0.5Ω - 0.6Ω
Clapton Wire: 24AWG and 30AWG, ~2.2mm Inner Diamater, 0.55Ω
Hive Wire: 26AWG, ~2.2mm Inner Diamater, 0.2Ω - 0.3Ω
Clapton II (Fused Clapton) Wire: 2x 28AWG and 32AWG, ~2.5mm Inner Diameter, 0.4Ω ± 0.05Ω
Clapton II (Fused Clapton) Wire: 2x 28AWG and 30AWG, ~2.5mm Inner Diameter, 0.4Ω ± 0.05Ω
Clapton III (Spaced Fused Clapton) Wire: 2x 28AWG and 0.5mm x 0.1mm Flat Wire, 32AWG, ~2.5mm Inner Diameter, 0.3Ω ± 0.05Ω
Clapton III (Spaced Fused Clapton) Wire: 2x 28AWG and 0.5mm x 0.1mm Flat Wire, 30AWG, ~2.5mm Inner Diameter, 0.3Ω ± 0.05Ω
Clapton Twist Wire: 2x 28AWG Twisted and 30AWG, ~2.5mm Inner Diameter, 0.4Ω ± 0.05Ω
Has anyone actually tried it and had decent results?
Haven't tried them as I wrap my own coils.
.
Last edited:
I straight up fused Clapton fits nicely but anything else is pretty tough on the screws.
Try some 26 or 24 gauge stainless, it's been my go to in the STM. Get flavor production and the ramp up is pretty damn fast.
Try some 26 or 24 gauge stainless, it's been my go to in the STM. Get flavor production and the ramp up is pretty damn fast.
@Ramsay Bolton THANKS!
@Marc411 "I straight up fused clapton..." does that mean you tried them on the STM? Where did you get the 26 or 24 stainless pre-built coils from? been looking for that to work with the kanger RBA. I don't want to wrap my own - would prefer to get pre-builts.
No problem!
UD also makes pre-built coils that will work fine (Not Stainless).
An inner diameter "ID" between 2.0 and 2.5mm works best for
me. I've tried 3.0mm with non-positive results.
You don't have to buy the coils here, but these would be what you are after
for plain wire pre-made coils:
50pcs UD Prebuilt Coils (Kanthal A1 26GA, 0.4 x ID2.5 x 0.5ohm)
50pcs UD Prebuilt Coils (Kanthal A1 26GA, 0.4 x ID2.5 x 0.5ohm)
FYI: Sounds like Mark411 might be wrapping his own coils like myself.
There are pre-made stainless steel coils out there, but their inner diameters
are too large.
.
3Fvape has prebuilt cheap and locally 101vape
And I get my straight stainless steel on ebay in 100ft lengths, the only drag is it doesn't come on spools but it's wrapped pretty well. Just search 316L Stainless Steel coils.
I.D -> Inner diameter isn't listed.
From what I've read, most are 3mm+, which won't work well.
As I mentioned: A 2-2.5mm Inner Diameter is best.
.
I sent an email to the company to ask. I'll post back if I hear anything in case others are interested
- Status
Similar threads
- Locked
