Clapton coils

[Fifty3]

So I just started getting into building more advanced coils. I built a Clapton w 20 gauge nichrome wrapped on 28 gauge nichrome and my reader says .1 but I think that's the loedt my trader reads. Is this safe I did 5 wraps at 2.5 mm. Single coil on a dually rda on a full copper rigmod v3.

 

[rob33]

ni-chrome and nickel have a really low resistance. I never go that low(.1), heard of some doing it on temperature builds. I have done 316L 2-28ga and 1-36ga that wrapped 3mm 5 times at .5

 

[Izan]

Hi and welcome,

Please, get an accurate ohm reader, before proceeding.

Cheers
I

 

[Fifty3]

ni-chrome and nickel have a really low resistance. I never go that low(.1), heard of some doing it on temperature builds. I have done 316L 2-28ga and 1-36ga that wrapped 3mm 5 times at .5

It fits nicely in my dually not getting too hot but will pretty hot.

 

[Don29palms]

So I just started getting into building more advanced coils. I built a Clapton w 20 gauge nichrome wrapped on 28 gauge nichrome and my reader says .1 but I think that's the loedt my trader reads. Is this safe I did 5 wraps at 2.5 mm. Single coil on a dually RDA on a full copper rigmod v3.

I wouldn't think of using that on a mech mod personally. If i build for my Tomahwk X I'll build no lower than .25 ohms. That's just me.

 

[Fifty3]

I wouldn't think of using that on a mech mod personally. If i build for my Tomahwk X I'll build no lower than .25 ohms. That's just me.

Even just a single coil on a rigmod with a single 18650. Is it not safe or is it just safe?

 

[puffon]

Not safe, if you don't KNOW what the ohms are, and if your battery can handle the amp draw.
Look at the chart Izan posted.

 

[Fifty3]

Not safe, if you don't KNOW what the ohms are, and if your battery can handle the amp draw.
Look at the chart Izan posted.

It says .1 but Ive never built lower than that so idk if my reader goes lower

 

[Fifty3]

It

It says .1 but Ive never built lower than that so idk if my reader goes lower

Its a coil master reader

 

[Topwater Elvis]

No, .1anything Ω it is not safe using a single cell mech.

 

[puffon]

IF it is .1 ohm you would need a battery that can handle a 42amp draw.
There are no 18650 batteries being made that can handle that.

 

[Don29palms]

I would suggest that you learn what is safe and what is not safe before you hurt yourself. An exploding battery is not a good thing. Please don't get hurt.

 

[r055co]

28g wrapping wire? Way, way to large, start with 34g or 36g.

Sent from my HTC 10 using Tapatalk

 

[Cosmic_Glaze]

Your battery can not handle it.... please listen to the advice you asked for. There is no need to vape at those ohms to get a satisfying flavorful vape.

 

[r055co]

I would suggest that you learn what is safe and what is not safe before you hurt yourself. An exploding battery is not a good thing. Please don't get hurt.

^^^^This

Single battery mechmod stick around 0.2 ohms

Sent from my HTC 10 using Tapatalk

 

[Kaimaikid]

Bugger that on a mech mod, even a 2 battery parallel mech mod is pushing it to the extreme limits, however on a regulated 2 battery plus mod likes of the Revenger should handle it with safety features built in.